Tomy SX-300E Скачать руководство пользователя страница 54

Страница: 54 / 60

ー 53 ー

Error code

Cause

Countermeasures

E20

The pressure in the chamber is high when the

power is turned ON.

Start operation after the pressure in the chamber falls to

0 MPa.

E21

The exhaust bottle is removed.

Attach the exhaust bottle.

E22

The exhaust hose is bent.

Turn OFF the power supply switch temporarily.

Reinsert the exhaust hose so that it is not bent.

The pressure rises because the form of articles

to be sterilized is likely to retain air.

Turn OFF the power supply switch temporarily. Open

the chamber lid after the pressure in the chamber falls to

0 MPa. Take countermeasures so that air can escape

easily from articles or reduce the volume of articles.

(Refer to 5-6. Placing articles to be sterilized.)

E23

The hole in the chamber (exhaust route) is

blocked with articles to be sterilized such as a

sterilizing bag.

Turn OFF the power supply switch temporarily. Open

the chamber lid after the pressure in the chamber falls to

0 MPa. Reattempt to place articles to be sterilized so that

the hole in the chamber is not blocked. If the mouth of

the sterilizing bag is closed, open it.

E24

The temperature in the chamber is 0℃ or less.

Operate the autoclave after the main unit is warmed

up to the temperature satisfying the environmental

condition.

E25

Control system abnormality.

Unplug the power plug of the autoclave from the outlet

and contact the dealer or business institution of our

company.

E29

Printing operation is performed while printing. Wait until the current printing has finished.

E30

Printer paper cover is open.

Close the paper cover.

Printer is out of paper.

Load paper into the printer.

Printer malfunction is suspected.

Stop operation and contact your dealer or local TOMY

representative.

No communication with the printer.

Wait until the current printing has finished and then

restart operation.
If no communication error occurs while no printing is

performed, stop operation and contact your dealer or

local TOMY representative.

Содержание SX-300E





























































Результаты поиска

Содержание SX-300E

Отзывы:

Бренды по названию

Популярные бренды

Tomy SX-300E, Руководство оператора

Результаты поиска

Содержание SX-300E

Отзывы:

Бренды по названию

Популярные бренды