Tomy SX-300E Скачать руководство пользователя страница 27

Страница: 27 / 60

ー 26 ー

Place articles to be sterilized in the stainless basket

normally attached or an optional stainless bucket.

※

Be careful not to hit articles to be sterilized on the

lid gasket or the temperature sensor when placing or

removing the articles. They may be damaged.

Place articles gently in the chamber.

※

Place articles so that they do not come above the

upper level of the lid hooks. When the chamber lid

is closed with articles placed above this level, they

may be damaged.

Close the chamber lid.

Placing articles to be sterilized

①

②

③

5-6. Placing articles to be sterilized

WARNING

Do not operate the autoclave with flammable or explosive articles in

place.

●

Contravention is dangerous with likelihood of fire or explosion.

Do not sterile sealed articles.

●

Contravention is dangerous with likelihood of burns

or serious accident due to blowout during removal

of articles. In addition, contravention is dangerous

with likelihood of damage to parts, or burns or serious

accident due to explosive breakage because the pressure

in the chamber may rise abnormally.

Do not sterilize glass equipment having cracks or

scratches.

●

Contravention is dangerous with likelihood of burns

or serious accident due to blowout during removal of

equipment.

Do not block the hole in the inside of the chamber with articles to be

sterilized.

●

Contravention is dangerous with likelihood of serious accident such as blowout

because the pressure in the chamber cannot be controlled when the hole at the

inside of the chamber is blocked with an article such as a sterilizing bag. Make

sure that articles are placed in the basket provided etc. so that the vicinity of the

hole is not blocked.

Upper level of lid hook

lid hook

Содержание SX-300E





























































Результаты поиска

Содержание SX-300E

Отзывы:

Бренды по названию

Популярные бренды

Tomy SX-300E, Руководство оператора

Результаты поиска

Содержание SX-300E

Отзывы:

Бренды по названию

Популярные бренды