Tomco DE89RB- 1000 Скачать руководство пользователя страница 83 | Manualshive

Страница: 83 / 87

Tomco DE89RB- 1000 Скачать руководство пользователя страница 83

CUSTOMER QUESTIONNAIRE

Name

Company

Phone Date

Application

1. How did you receive this manual? Was the manual . . .

             a.       Included in a product shipment?          d.      Given to you by a colleague?
             b.      Given to you by management?             e.      Other?
             c.       Purchased by you?

2. How frequently do you use this manual?

             a.       Quarterly                                                    d.      Daily
             b.      Monthly                                                     e.      Hourly
             c.       Weekly                                                       f.       Seldom

3. Under what circumstances do you use this manual?

4. Describe the last time you used this manual.

5. What task or project were you performing when you used this manual?

6. How do you use this manual? Do you . . .

             a.       Sit down and read it?
             b.      Refer to a certain section while performing a task or project?
             c.       Look up information for someone else?
             d.      Refer to it only when you have a problem to solve?
             e.       Other?

7. How do you look up information in this manual? Do you . . .

             a.       Use the table of contents?
             b.      Flip through the pages until you locate the right section?
             c.       Flip to the tabbed sections, then proceed to locate information?
             d.      Other?

8. When you use this manual, how easy is it to find information? Do you . . .

             a.       Always locate the right section immediately?
             b.      Sometimes turn to another section before you locate the right one?
             c.       Take more than three times to locate information?
             d.      Fail to locate information?

9. Do you record notes in the margins of this manual?

Yes

No

10. If yes, what notes do you write down?

continued on other side

User-Friendliness

7.16

Please Complete and Mail to:

TOMCO

2

EQUIPMENT COMPANY

         Engineering Department
         3340 Rosebud Rd.
         Loganville, GA 30052 USA

or fax to:

(770) 985-9179

APPENDIX

«
...
81
82
83
84
85
...
»

Содержание DE89RB- 1000
























































































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды