manualshive.com logo in svg

Tomco DE89RB- 1000, Руководство по эксплуатации и техническому обслуживанию

Поделиться
Скачать
Tomco DE89RB- 1000 Скачать руководство пользователя страница 21

INSTALLATION 

Note: If isolation valves are included in the connecting lines (steps 1 & 2),             

     you must install a safety relief valve between the optional isolation valve and        

     the liquid or vapor process isolation valves at the storage unit in the event                

     that carbon dioxide becomes trapped between the two valves. 

         

3. Install a low-pressure check valve (no greater than 5 psi cracking pressure) on the 

exhaust port of each heat exchanger  and vent to the outdoors using either a flexi-

ble hose or suitable piping.  Tomco

2

 Parts and Service can supply the check 

valves and piping if needed. Slope piping at least 1/4” per foot (20mm per meter) 

away from the pelletizer and include a downturn in the piping to prevent moisture 

from entering the pelletizer. 

Note:  Forced air ventilation is not a sufficient means of removing carbon                      

       dioxide vapor.  The exhaust ports must be vented to the outdoors. 

4. Fill the hydraulic fluid reservoir to the top of the sight glass with a good quality 

hydraulic fluid (Rando HD68 or equal) with a fluid viscosity of 150-300 SUS 

(ISO 32-68) @ 100 ºF (37.7 ºC). 

3.2 

DANGER 

CARBON DIOXIDE IS AN ASPHYXIANT AND 
WHEN RELEASED IN HIGH CONCENTRATIONS 
AND IN CONFINED AREAS CAN CAUSE SUFFO-
CATION AND DEATH! CO2 VAPOR IS HEAVIER 
THAN AIR AND WILL ACCUMULATE IN LOW AR-
EAS OR DEPRESSIONS. 

DANGER 

TRAPPING CARBON DIOXIDE IN A PIPE WITH-
OUT A SAFETY RELIEF VALVE CAN RESULT IN 
A RUPTURE OF THE PIPE CAUSING SERIOUS 
INJURY OR DEATH! 

Содержание DE89RB- 1000
























































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды