Tomco DE89RB- 1000 Скачать руководство пользователя страница 62

Страница: 62 / 87

REPAIR & ADJUSTMENTS

4. When the pressure switch shifts at 2900 PSI the cylinder continues to advance at an

18 GPM flow rate and the pressure increases (due to ice compression resistance) to

approx. 3200-3600 PSI. The ice slug moves and extrudes ice through the die until

the end of stroke limit switch (extend) is tripped.

Note: The pressure drops off slightly when the ice slug begins to move.

5. When the cylinder reaches the end of the extend stroke and signals the processor

(end of stroke limit switch), the following happens:

A. Valve #26 shifts to decompression and valve #28 opens to decompress the system

pressure.

B. Valve #20 directional control de-energizes and shifts from extend to the center

position (all ports closed).

C. The cylinder stops its advance travel.

6. Direction control valve #20 energizes and shifts to retract the cylinder. The cylinder

will begin retracting because:

A. Pump #1 shifts to full flow (60 GPM)

B. Pump #2 shifts to full flow (25 GPM)

C. Dump valve #28 closes

D. Valve #26 shifts from decompression to excess flow position.

7. When the cylinder has traveled to a point near the full retracted position it trips a re-

tracted limit switch, and the following happens:

A. Pump #2 shifts to min-volume (18 GPM)

B. Pump #1 shifts to the 450 PSI (unload) setting

C. Valve #28 is energized and dumps partial pump flow to tank

6.7

Содержание DE89RB- 1000
























































































Результаты поиска

Содержание DE89RB- 1000

Отзывы:

Похожие инструкции для DE89RB- 1000

Бренды по названию

Популярные бренды

Tomco DE89RB- 1000, Руководство по эксплуатации и техническому обслуживанию

Результаты поиска

Содержание DE89RB- 1000

Отзывы:

Похожие инструкции для DE89RB- 1000

Бренды по названию

Популярные бренды