Tomco DE89RB- 1000 Скачать руководство пользователя страница 20

Страница: 20 / 87

INSTALLATION

Following is the standard installation procedure for a Tomco

Equipment Co. carbon

dioxide dry ice pelletizer.

Note: This should be performed by a qualified carbon

dioxide equipment technician only.

Refer to Figure 3.1 on page 3.3.

Note: A liquid CO

supply pressure of 250 to 300 psig (17.23 to 20.68 bar) is re-

quired for satisfactory performance. Contact Tomco

Equipment Co. if liquid CO

pressure will be lower than 250 psig (17.23 bar). Contact Tomco

Equipment Co. if

liquid CO

Dew point will be above –60°F (-51.1°C).

1. Install an insulated connecting line between the liquid process isolation valve on

the carbon dioxide storage unit and the 1” FNPT (1/2” on 100lb and 200lb ma-

chines) (1 1/2” on high capacity machines) connection on the rear of the pellet-

izer. We recommend that you use pre-insulated (2 1/2” (63.5 mm) urethane) 1

1/8” (1 5/8” on high capacity) Type K copper. However, 1” NPT (1 1/2” on high

capacity) schedule 80 seamless pipe can be substituted. Include in this line a core

type liquid CO

filter. We recommend a Sporlan Valve Co. model C-1449G for

1 1/8” copper or a Sporlan Valve Co. model C-1448P for 1” NPT pipe. Each of

these filters uses a single Sporlan Valve Co. core model RC-4864. (Filters are

available from Tomco

Parts and Service.) This line should be no longer than

25’ (7.62 m). Tomco

recommends the use of an automatic vapor purge device

on any pelletizer that has more than 25’ (7.62m) of liquid supply piping. Con-

tact Tomco

Equipment Co. if the installation will require more than

25’ (7.62m) of liquid supply piping. The above is for a single machine operation.

If several machines are connected to the same liquid line, consider using sizes

larger than mentioned above.

Using an undersized liquid line will result in decreased production.

2. Install a connecting line between the vapor process isolation valve on the carbon

dioxide storage unit and the 1/4” FNPT connection on the rear of the pelletizer.

The construction material of this line is not critical and is up to the installer’s dis-

cretion, but it must be approved for at least 350 psig (24.1 bar).

3.1

Содержание DE89RB- 1000
























































































Результаты поиска

Содержание DE89RB- 1000

Отзывы:

Бренды по названию

Популярные бренды

Tomco DE89RB- 1000, Руководство по эксплуатации и техническому обслуживанию

Результаты поиска

Содержание DE89RB- 1000

Отзывы:

Бренды по названию

Популярные бренды