Tomco DE89RB- 1000 Скачать руководство пользователя страница 64

Страница: 64 / 87

REPAIR & ADJUSTMENTS

3. Valve #26 (excess flow)

Valve #26 is energized and shifted to the excess flow position 200 microseconds after

valve 20 is shifted to the retract travel position.

Dry Ice Extrusion Process (start-up)

Note: When the cycle start is activated the microprocessor will determine if “A” cylin-

der has been selected, "B" cylinder has been selected or "Both" cylinders have been se-

lected to operate.

1. If "A" or "A&B" have been selected for an operation mode the first function will be

a clean out stroke on "A" (then a clean out stroke on "B"' if A&B were selected).

2. If "B"' had been selected then a clean out stroke on cylinder "B" is the only function.

Note: Clean out stroke consists of injection of C0

w/valve #2 for a preset injection

time then check for ice plug by sensing pressure on PS-1

3. If PS-1 senses pressure on clean out stroke, then the sequence shifts to normal opera-

tion.

4. If PS-1 does not sense pressure due to the presence of an ice plug. The machine goes

into a series of five (5) cool down cycles.

A. #1 inject CO

, with valve #3 for 1 minute (extrude and return)

B. #2 inject C0

with valve #3 for 1 minute (extrude and return)

C. #3 inject C02 with valve #3 for 1 minute (extrude and return)

D. #4 inject C02 with valve #3 for 1 minute (extrude and return)

E. #5 inject C02 with valve #3 for 1 minute (extrude and return)

5. Inject C02 with valve #2 and check for plug (pressure switch PS-1)

A. If PS-1 senses pressure the sequence will shift to normal operation.

6.9

Содержание DE89RB- 1000
























































































Результаты поиска

Содержание DE89RB- 1000

Отзывы:

Похожие инструкции для DE89RB- 1000

Бренды по названию

Популярные бренды

Tomco DE89RB- 1000, Руководство по эксплуатации и техническому обслуживанию

Результаты поиска

Содержание DE89RB- 1000

Отзывы:

Похожие инструкции для DE89RB- 1000

Бренды по названию

Популярные бренды