TLV Cospect MC-COS-16 Скачать руководство пользователя страница 18 | Manualshive

Страница: 18 / 37

background image

172-65169MA-08 (MC-COS Multi-control Valve) 28 May 2010

17

Wiring

Wiring Notes

Background electromagnetic noise that has no effect on analog equipment may
cause digital equipment to malfunction or fail. To prevent adverse effects from
electro-magnetic (EM) interference, carefully follow the wiring instructions below:

1. Power Source

1) If there is EM noise from the power source, a filter should be used. To prevent

interference, do not bundle the EM filter's power source input and output lines
together.

2) Although there is a built-in fuse in the controller, there is no power switch. It is

required that a power switch be installed on an external circuit near the main
unit. Do not install a power switch between the EM filter and the valve, as this
will reduce the effectiveness of the filter.

3) A power cable is not included with the unit. See “Wiring Instructions”.

4)

Install an overcurrent protection device on the power supply lines (both poles)

to prevent overcurrent.
Recommended rating of the device: 250V/2A, Delay type

2. Input/Output Signal Lines for Valve Operation

1) Use shielded cables for the I/O signal lines.

Connect the shielded cables to the receiver's shield terminal.

2) Separate the I/O signal cables from power cables, drive cables, and EM noise-

generating equipment. Do not insert I/O signal cables in common piping or
ducts with aforementioned cables.

3. Ground

1) Be sure to ground the MC-COS and the controller.
2) Use a one-point ground at the same point as the ground for the controller to be

used with the valve. Do not use extension wiring. Failure to ground the valve as
specified may cause it to malfunction.

3) For the ground terminal, use a flexible copper wire, at least 2 mm

2

(0.003 in

2

).

Ground with a ground resistance of 100

Ω

or less (Class 3 ground).

EM Signal

Filter

Power

Supply

Drive

Section

Terminal

Block

Drive

Section

Terminal

Block

Controller

Terminal

Block

Drive

Section

Terminal

Block

Controller

Terminal

Block

Shield

Shielded

Cable

MC-COS

MC-COS

Power

Switch

MC-COS

Power

Supply

Power

Supply

Ground

«
...
16
17
18
19
20
...
»

Содержание Cospect MC-COS-16






































Отзывы:

Нет отзывов

Похожие инструкции для Cospect MC-COS-16

Бренд: ABB Страницы: 2

Бренд: Falcon Страницы: 3

Бренд: Eaton Страницы: 166

Бренд: Vacon Страницы: 64

Бренд: Valor Страницы: 20

Бренд: CAME Страницы: 98

Бренд: CAME Страницы: 16

Бренд: CAME Страницы: 8

Бренд: MAKOT Страницы: 6

Бренд: Kampmann Страницы: 5

Бренд: SYCLOPE electronic Страницы: 40

Бренд: Timotion Страницы: 10

Бренд: East Coast Datacom Страницы: 14

Infi 90 IMSPM01

Бренд: Bailey Страницы: 52

Бренд: M-system Страницы: 5

Бренд: Satel Страницы: 7

Бренд: Anritsu Страницы: 54

Бренд: Governors America Страницы: 6

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды