manualshive.com logo in svg

TLV Cospect MC-COS-16, Инструкция по эксплуатации

Поделиться
Скачать
TLV Cospect MC-COS-16 Скачать руководство пользователя страница 2

 

172-65169MA-08 (MC-COS Multi-control Valve)    28 May 2010

 

1

Contents 

 

Introduction ........................................................................ 1

 

Safety Considerations ........................................................ 2

 

Specifications ..................................................................... 4

 

Correct Usage of the 

MC-COS

 Multi-control Valve ............ 6

 

Configuration...................................................................... 8

 

Installation ........................................................................ 10

 

Wiring Instructions............................................................ 17

 

Setting the Valve Coefficient ............................................ 19

 

Operation ......................................................................... 20

 

Inspection and Maintenance ............................................ 22

 

Disassembly..................................................................... 23

 

Reassembly ..................................................................... 29

 

Troubleshooting ............................................................... 30

 

Product Warranty ............................................................. 36

 

 

 

Introduction 

 

Thank you for purchasing the

 

MC-COS

 high-precision multi-control 

valve for steam. 
This product has been thoroughly inspected before being shipped from the 
factory. When the product is delivered, before doing anything else, check the 
specifications and external appearance to make sure nothing is out of the 
ordinary. Also be sure to read this manual carefully before use and follow the 
instructions to be sure of using the product properly. 
Steam-using equipment can achieve its intended efficiency only if the steam 
being used is very dry. Using steam in which matter such as condensate, 
scale, types of grease or air is entrained can not only result in problems with 
the steam-using equipment and in lowered productivity, but can also lead to 
shortened service life for and malfunction of the multi-control valves. 

The

 high-precision multi-control valve, model 

MC-COS

, provides 

accurate pressure control (MC-COS-3, MC-COS-16) and temperature control 
(MC-COS-16) when combined with the

  SC-F70 digital indicator 

controller or the SP-F70 programmable indicator controller. 
If detailed instructions for special order specifications or options not contained 
in this manual are required, please contact

  for full details. 

This instruction manual is intended for use with the model(s) listed on the front 
cover. It is needed not only for installation, but also for subsequent 
maintenance, disassembly/reassembly and troubleshooting. Please keep it in 
a safe place for future reference. 

Содержание Cospect MC-COS-16






































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды