TLV Cospect MC-COS-16 Скачать руководство пользователя страница 36

Страница: 36 / 37

172-65169MA-08 (MC-COS Multi-control Valve) 28 May 2010

Malfunctions and Countermeasures

○

:OFF

●

:ON

LE 4, 3, 2, 1

Malfunction Details

Performance of the

actuator when

abnormality occurs

Remedy

○○○○

No malfunction is
detected (All LEDs
are normally OFF)

Continuous operation

○○○●

Operation signal
input error

Continuous operation

Operation input signal is
abnormal.
Make sure that there is no
abnormality with the
controller and the cable for
the operation input signal.

●○○○

Temperature in the
actuator is abnormal

Continuous operation

Make sure that the
temperature around the
drive section is within the
specification range (0 to
50 °C (32 – 122 F°).

○○●●

Motor is overloaded

Motor shuts down, then
keeps rebooting after a
few seconds.

Motor is abnormally
overloaded. Contact TLV.

○●○●

Low motor load
(reducer gear wear,
motor slippage)

Continuous operation

Possibility of abnormal wear
of the gear in the reducer.
Contact TLV.

●○○●

Potentiometer signal
error

Stops when
malfunction occurs

Potentiometer is abnormal.
Contact TLV.

●○●○

Initialization error

Stops when
malfunction occurs

●●○○

PROM Store Error Stops when

malfunction occurs

If the same phenomenon
occurs after switching the
power OFF and ON, contact
TLV.

○●●●

Motor drive power
voltage is abnormal

Continuous operation Possible abnormality of the

power supply circuit.
Contact TLV.

●○●●

CPU Error

Stops when
malfunction occurs

If the same phenomenon
occurs after switching the
power OFF and ON, contact
TLV.

●●●○

External clock stops

Continuous operation
using internal clock

●●●●

Mode Setting Error

Stops

Possible abnormality of the
internal circuit.
Contact TLV.

○○●○

(spare) Continuous

operation

○●○○

(spare) Continuous

operation

○●●○

(spare) Continuous

operation

●●○●

(spare) Continuous

operation

Содержание Cospect MC-COS-16






































Результаты поиска

Содержание Cospect MC-COS-16

Отзывы:

Похожие инструкции для Cospect MC-COS-16

Бренды по названию

Популярные бренды

TLV Cospect MC-COS-16, Инструкция по эксплуатации

Результаты поиска

Содержание Cospect MC-COS-16

Отзывы:

Похожие инструкции для Cospect MC-COS-16

Бренды по названию

Популярные бренды