Titan PowerLiner 3100 Скачать руководство пользователя страница 23

Страница: 23 / 28

Pressure Switch Replacement

WARNING: Before proceeding, follow the Pressure
Relief Procedure outlined on page 5. Additionally, fol-
low all other warnings to reduce the risk of an injection
injury, injury from moving parts or electric shock.

1. Remove socket head cap screws.
2. Remove electrical cover plate #60 (on pg. 20), located

near pressure switch and disconnect two red wires from
clutch starter #58 (on pg. 20).

3. Remove screw #27 (on pg. 20) from pressure switch

adjustment knob and slide knob off.

4. Remove screw #27 (on pg. 20) located on side of gear

box housing #53 (on pg. 20) and using a 1/8" allen
wrench remove set screw #56 (on pg. 20), until pressure
switch #3 is able to slide down through. Feed electrical
wires down at the same time.

5. Insert new switch assembly #3 into housing while

carefully working the wires into the switch box. Using
needle nose pliers, reconnect wires to motor starter.

6. Making sure that the switch assembly is fully inserted,

tighten set screw #56 (on pg. 20) with a 1/8" allen wrench
until the switch assembly is secure. Reattach adjustment
knob #26 (on pg. 20).

7. Inspect O-Rings #4 and #5 on switch assembly.
8. Install insulator plate #66 (on pg. 20) and plate #60 (on

pg. 20).

9. The pressure switch is factory calibrated so no

adjustment is required.

Service / Replacement of the Pressure
Relief Prime Valve

WARNING: Before proceeding, follow the Pressure Relief
Procedure outlined on Page 5. Additionally, follow all
other warnings to reduce the risk of an injection injury,
injury from moving parts or electric shock.

1. Remove the Dowel Pin #17 from Bypass Valve Handle

#18.

2. Remove Handle #18 and Bypass Cam #16.
3. Using a wrench, loosen Bypass Housing #11 and

unscrew.

4. Unscrew Bypass Retainer #15 and remove Bypass Valve

Stem #13.

5. Inspect ball on end of Stem #13 and O-Ring #12. Clean

or replace if worn.

6. Screw completed assembly into Filter Block #25. Tighten

securely with wrench.

7. Install Bypass Cam #16 over Bypass Retainer #15,

lubricate with grease. Line up Dowel Pin #17 on Cam
#18 with hole on Filter Block #25.

8. Using Dowel Pin #17 line up Stem #13 with hole on

Handle #18. Secure Handle with Dowel Pin #17.

9. IMPORTANT: If Handle #18 rotates 360° check Pin on

Cam #16.

Service / Replacement of Filter

Pump Filter

1. Unscrew Filter Housing #21.
2. Remove Filter Cartridge #22. Clean or replace.
3. Inspect O-Ring #24. Clean or replace.
4. Reattach Filter Housing #21.

Gun Filter

WARNING: Follow all safety precautions as described in
high pressure warning section before proceeding. If your
spray gun leaks or spits at the tip when you release the
trigger, the needle or seat is dirty, worn or damaged and
must be cleaned or replaced.

Replacement or Removal of Filter:

1. First pull down on trigger safety guard and swing away

from handle.

2. Unscrew handle from spray head.
3. Unscrew left hand threaded filter from spray head.

4. Screw new or cleaned filter into the head. (To reinstall left

hand thread turn counterclockwise.)

5. Reattach handle to head and secure safety trigger guard.

Figure 9

For more detail, part number information and assem-

bly drawings at larger scale, please see the SGX-20
Professional Airless Gun Owner’s Manual (#313-001).

NOTE: If filter breaks off in the head use a small

wood screw to remove.