8. Move the PRIME/SPRAY valve up to the SPRAY position.
9. Turn the unit on.
10. Unlock the gun by turning the gun trigger lock to the
unlocked position.
Ground the gun by holding it against
the edge of the metal container while
flushing. Failure to do so may lead to
a static electric discharge, which may
cause a fire.
11. Trigger the gun into the metal waste
container until the old solvent is gone and fresh solvent is
coming out of the gun.
12. Lock the gun by turning the gun
trigger lock to the locked position.
13. Set down the gun and increase the
pressure by turning the pressure
control knob slowly clockwise into
the green zone.
14. Check the entire system for leaks.
If leaks occur, follow the “Pressure
Relief Procedure” in this manual before tightening any
fittings or hoses.
15. Follow the “Pressure Relief Procedure” in this manual
before changing from solvent to paint.
Be sure to follow the pressure relief procedure when
shutting the unit down for any purpose, including
servicing or adjusting any part of the spray system,
changing or cleaning spray tips, or preparing for cleanup.
Painting
1. Place the siphon tube into a container of paint.
2. Place the return hose into a metal waste container.
3. Set the pressure to minimum by turning
the pressure control knob to the “Min”
setting in the yellow zone.
4. Move the PRIME/SPRAY valve down to
the PRIME position.
5. Turn the unit on by moving the ON/OFF
switch to the ON position.
6. Allow the sprayer to run until paint is coming through the
return hose into the metal waste container.
7. Turn the unit off by moving the ON/OFF switch to the OFF
position.
8. Remove the return hose from the waste container and
place it in its operating position above the container of
paint.
9. Move the PRIME/SPRAY valve up to the SPRAY position.
10. Turn the unit on.
11. Unlock the gun by turning the gun trigger lock to the
unlocked position.
Ground the gun by holding it against
the edge of the metal container while
flushing. Failure to do so may lead to
a static electric discharge, which may
cause a fire.
12. Trigger the gun into the metal waste
container until all air and solvent is flushed from the spray
hose and paint is flowing freely. from the gun.
WARNING
Max.
PSI
Cle
an
Min.
PSI
WARNING
Trigger lock
in locked position.
WARNING
NOTE: Make sure that the spray gun does not have a
tip or tip guard installed.
13. Lock the gun by turning the gun
trigger lock to the locked position.
14. Turn the unit off.
15. Attach tip guard and tip to the gun
as instructed by the tip guard or tip
manuals.
POSSIBLE INJECTION HAZARD. Do not spray without the
tip guard in place. Never trigger the gun unless the tip is
in either the spray or the unclog position. Always engage
the gun trigger lock before removing, replacing or
cleaning tip.
16. Turn the unit on.
17. Increase the pressure by turning the pressure control
knob slowly clockwise toward the green zone and test the
spray pattern on a piece of cardboard. Adjust the
pressure control knob until the spray from the gun is
completely atomized. Try to keep the pressure control
knob at the lowest setting that maintains good
atomization.
Electronic Pressure Control Indicators
The following is a description of the indicators on the electronic
pressure control.
Pressure Relief Procedure
Be sure to follow the pressure relief procedure when
shutting the unit down for any purpose, including
servicing or adjusting any part of the spray system,
changing or cleaning spray tips, or preparing for cleanup.
1. Lock the gun by turning the gun
trigger lock to the locked position.
2. Turn the unit off by moving the
ON/OFF switch to the OFF position.
3. Turn the pressure control knob
counterclockwise to its OFF position
in the black zone.
4. Unlock the gun by turning the gun trigger lock to the
unlocked position.
5. Hold the metal part of the gun firmly to
the side of a metal container to ground
the gun and avoid a build up of static
electricity.
6. Trigger the gun to remove any
pressure that may still be in the hose.
7. Lock the gun by turning the gun trigger lock to the locked
position.
8. Move the PRIME/SPRAY valve down to the PRIME
position.
Trigger lock
in locked position.
WARNING
Pressure
Indicator
Motor Running Indicator
Programmer Port
Programmer Port
Dust Cover
Circuit
Breaker
Blinking Yellow =
0 PSI – priming pressure
Solid Yellow =
priming pressure – 1800 PSI
Solid Green =
1800 PSI – 3300 PSI
NOTE: Turning the pressure up higher then needed to
atomize the paint will cause premature tip wear
and additional overspray.
WARNING
Trigger lock
in locked position.
© Titan Tool Inc. All rights reserved.
5
