Thermo Scientific VARIOKLAV 25T Скачать руководство пользователя страница 55 | Manualshive

Страница: 55 / 60

background image

12 Troubleshooting

03/2007

55

DA0621_a/

12 Troubleshooting

The program control is equipped with a sophisticated error management system. If
an error occurs during program execution, an error message is shown in the cycle
display (16) or the current values display (13).
If an error occurs:

♦

Memorize or write down the error message.

♦

Press the START/STOP key (19).

This will interrupt the program cycle. The sterilizer is returned to a safe state.

♦

Before restarting the program, troubleshoot the problem (see Table 5).

Message in the
cycle display

Meaning Remedy

Error 2
Lock open

Locking levers do not attain their
maximum closing positions.

Open and close door; if
necessary, contact
after-sales service

Error 3
No p.- buildup

Door seal cannot build pressure:

Compressor missing or defective, or
pressure line missing or interrupted,
or door seal missing

Contact after-sales
service.

Error 4
Seal defective

Door seal builds but cannot keep
pressure:

Seal leaking, or
pressure tank leaking, or
pressure line leaking.

Contact after-sales
service:

Have leaking part
replaced

Error 6
Compressor

Door seal loses pressure during
sterilization:
Compressor defective.

Contact after-sales
service.

Error 9
Running dry

The heater has overheated because
the jacket space has run dry.
Or the overtemperature limiter was
set too low (required setting: 170 °C)
and was therefore activated.

Contact after-sales
service.

Error 10
Control error

Internal program control error.

Turn off and restart the
sterilizer; contact after-
sales service.

Error 12
Water low

Feed water tank empty, or
valves (Y3, Y6.1, Y6.2) defective, or
external water supply (option)
defective.

Fill feed water tank or
contact after-sales
service; check external
water supply where
applicable.

«
...
53
54
55
56
57
...
»

Содержание VARIOKLAV 25T





























































Отзывы:

Нет отзывов

Похожие инструкции для VARIOKLAV 25T

Бренд: 3M Страницы: 2

Бренд: Dawn Страницы: 8

Бренд: BACtrack Страницы: 13

Бренд: Badgematic Страницы: 28

Бренд: BACtrack Страницы: 2

Бренд: MADRIX Страницы: 28

Бренд: BACTcontrol Страницы: 28

Бренд: dbx Страницы: 12

Бренд: dbx Страницы: 13

Бренд: dbx Страницы: 72

Бренд: dbx Страницы: 11

Бренд: dbx Страницы: 16

Бренд: Ecler Страницы: 108

Бренд: R&S Страницы: 121

Бренд: xsto Страницы: 76

Бренд: F&V Страницы: 5

Бренд: F Care Systems Страницы: 2

Бренд: JBSYSTEMS Light Страницы: 17

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды