Thermo Scientific Orion AQUAfast AQ3010 Скачать руководство пользователя

Страница: 5 / 39

Thermo Scientific Orion AQUAfast AQ3010 Turbidity Meter User Guide

Chapter 1

ntroduction

This user guide contains information on the preparation, operation

and maintenance of the Thermo Scientific Orion AQUAfast® AQ3010

turbidity meter . This user guide provides both a step by step guide to

help you operate the waterproof AQ3010 turbidity meter and serves as a

handy reference guide .

Follow the basic instructions contained in this user guide during the

operation, care and maintenance of the meter . The safety protections

provided by this equipment may be impaired if it is used in a manner not

described in this user guide . It is recommended that all operators should

read this user guide prior to working with this meter .

The manufacturer will not accept any responsibility for damage or

malfunction to the meter caused by improper use of the instrument .

The information presented in this user guide is subject to change without

notice as improvements are made, and does not represent a commitment

on the part of the manufacturer .

Note:

The manufacturer reserves the right to make improvements in

design, construction and appearance of products without notice .

Thank you for selecting the waterproof portable AQ3010 turbidity

meter . The AQ3010 meter allows you to measure turbidity of an aqueous

sample in the field . This instrument operates on the nephelometric

principle of turbidity measurement and is designed to meet the criteria

specified in ISO 7027 and DIN 27027 standards . See the

Measurement

Principle

section .

General

nformation

AQ3010 Meter

Overview

Содержание Orion AQUAfast AQ3010








































Результаты поиска

Содержание Orion AQUAfast AQ3010

Отзывы:

Похожие инструкции для Orion AQUAfast AQ3010

Бренды по названию

Популярные бренды

Thermo Scientific Orion AQUAfast AQ3010, Руководство пользователя

Результаты поиска

Содержание Orion AQUAfast AQ3010

Отзывы:

Похожие инструкции для Orion AQUAfast AQ3010

Бренды по названию

Популярные бренды