Thermo Scientific Orion AQUAfast AQ3010 Скачать руководство пользователя

Страница: 28 / 39

Thermo Scientific Orion AQUAfast AQ3010 Turbidity Meter User Guide

LCD
Message

Description

Corrective Actions

ERR 8

Excessive stray light detected.

Verify that the vial is fully in the

sample well and light shield cover

is properly placed over the vial.

Attempting a measurement when

low battery indicator is on.

Replace the batteries.

ERR 9

Lamp failure.

Contact Technical Support.

Turbidity value is above the

measurement range (>1000 NTU).

Dilute sample, see the

Dilution

section.

Low battery indication – the

batteries need to be replaced.

Replace the batteries.

Note:

If an error message appears, take the

appropriate corrective action and re-do the

desired procedure . If the problem persists,

contact Technical Support or your dealer .

After troubleshooting all components of your measurement system,

contact Technical Support . Within the United States call 1 .800 .225 .1480

and outside the United States call 978 .232 .6000 or fax 978 .232 .6031 .

In Europe, the Middle East and Africa, contact your local authorized

dealer . For the most current contact information, visit

www .thermo .com/contactwater .

For the most current warranty information, visit www .thermo .com/water .

The AQ3010 meter is supplied with a 3 year warranty from

manufacturing defects and calibration standards for 6 months . If

repair or adjustment is necessary and has not been the result of abuse or

misuse within the designated period, please contact Technical Support

or your dealer for an RMT number . A repair technician will determine

if the product problem is due to deviations or customer misuse . Out of

warranty products will be repaired on a charged basis .

The instrument warranty shall not apply to defects resulting from:

• Improper or inadequate maintenance by customer

• Unauthorized modification or misuse

• Operation outside of the environment specifications of the products

Waterproof Seal:

Opening the instrument enclosure (excluding the

battery compartment) may void the warranty .

Assistance

Warranty

Exclusions

Содержание Orion AQUAfast AQ3010








































Результаты поиска

Содержание Orion AQUAfast AQ3010

Отзывы:

Похожие инструкции для Orion AQUAfast AQ3010

Бренды по названию

Популярные бренды

Thermo Scientific Orion AQUAfast AQ3010, Руководство пользователя

Результаты поиска

Содержание Orion AQUAfast AQ3010

Отзывы:

Похожие инструкции для Orion AQUAfast AQ3010

Бренды по названию

Популярные бренды