Thermo Scientific Orion AQUAfast AQ3010 Скачать руководство пользователя

Страница: 9 / 39

Thermo Scientific Orion AQUAfast AQ3010 Turbidity Meter User Guide

Figure 3

Keypad

read

enter

cal

Turbidity Meter

Chlorine Colorimeter

read

enter

zero

mode

Keys and

Functions

The keypad has five keys:

ON/OFF

CAL

▲

▼

and

READ/ENTER

Key

Functions

CAL

READ

ENTER

Powers on and off the meter. The meter automatically

shuts off 20 minutes after last key press to conserve the

battery life.

CAL

READ

ENTER

Initiates the calibration mode of the meter. When pressed,

the meter is set to accept the first calibration standard.
It is also used to exit the calibration mode if the user does

not want to follow the complete calibration procedure.

CAL

READ

ENTER

When in measurement mode, the

READ/ENTER

key is used

to perform a measurement.
Single-shot measurements: When the key is pressed and

released immediately (a quick key stroke of less than 0.3

seconds), the display will blink [-Rd-] ten times and display

the measured value.
Continuous measurements: If the

READ/ENTER

key is

pressed and held, the instrument will perform a continuous

measurement during which the display is updated every

2 seconds. This can be used for indexing vials. (This

function is not available in calibration mode). After

the

READ/ENTER

key is released, the instrument will

automatically perform a single-shot measurement.

CAL

READ

ENTER

CAL

READ

ENTER

Active only during calibration mode. These scroll keys are

used to select the next calibration point.
Note: After the successful calibration of one point, the

meter automatically selects the next calibration point, or

automatically exits the calibration mode after the fourth

calibration point.

Содержание Orion AQUAfast AQ3010








































Результаты поиска

Содержание Orion AQUAfast AQ3010

Отзывы:

Похожие инструкции для Orion AQUAfast AQ3010

Бренды по названию

Популярные бренды

Thermo Scientific Orion AQUAfast AQ3010, Руководство пользователя

Результаты поиска

Содержание Orion AQUAfast AQ3010

Отзывы:

Похожие инструкции для Orion AQUAfast AQ3010

Бренды по названию

Популярные бренды