Thermo Scientific Orion AQUAfast AQ3010 Скачать руководство пользователя

Страница: 32 / 39

Thermo Scientific Orion AQUAfast AQ3010 Turbidity Meter User Guide

Parameter

Specification

Measurement Method

ISO 7027 compliant nephelometric

method (90°)

Measurement Range

0 to 1000 NTU

Automatic Range Selection

0.01 to 19.99 NTU

20.0 to 99.9 NTU

100 to 1000 NTU

Resolution

0.01 NTU (0 to 19.99 NTU)

0.1 NTU (20 to 99.9 NTU)

1 NTU (100 to 1000 NTU)

Precision

±2% of reading ± 1 LSD for 0 to 500 NTU;

±3% of reading ± 1 LSD for 501 to 1000 NTU

Calibration Standards

0.02 NTU, 20 NTU, 100 NTU, 800 NTU

Standardization

EPA approved polymer-based primary

standards

Light Source

Infrared-emitting diode (850 nm wavelength)

Light Source Life

> 1,000,000 tests

Detector

Silicon photovoltaic

Stray Light

< 0.02 NTU

Display

4 digit 14 segments customized liquid crystal

display with annunciators

Sample Vials (Cuvettes)

Glass vials with screw caps, fill line and

indexing mark, 51 (H) x 25 (Dia) mm ( 2 x 1 in)

Sample Volume Required

10 mL (0.33 oz)

Operating Temperature Range

0 °C to 50 °C (32 °F to 122 °F)

Sample Temperature Range

0 °C to 50 °C (32 °F to 122 °F)

Operating Humidity Range

0 to 90% relative humidity,

non-condensing at 30 °C (86 °F)

Power Supply

4 x AAA alkaline batteries

Battery Life

> 1200 readings

Enclosure Type

ABS plastic

Waterproof Rating:

IP67

Regulatory Certification

CE, cTUVus, TUV 3-in-1, FCC part 15

Insulation Rating

Pollution Degree 2

Weight:

Meter: 0.23 kg (0.51 lb)
Meter with case: 2.0 kg (4.4 lb)

Dimensions

Meter: 7.9 (W) x 17.2 (L) x 5.0 (H) cm

(3.1 x 6.8 x 2.0 in)

Meter & case: 35 (W) x 27 (L) x 15 (H) cm

(13.8 x 10.6 x 5.9 in)

Specifications

Содержание Orion AQUAfast AQ3010








































Результаты поиска

Содержание Orion AQUAfast AQ3010

Отзывы:

Похожие инструкции для Orion AQUAfast AQ3010

Бренды по названию

Популярные бренды

Thermo Scientific Orion AQUAfast AQ3010, Руководство пользователя

Результаты поиска

Содержание Orion AQUAfast AQ3010

Отзывы:

Похожие инструкции для Orion AQUAfast AQ3010

Бренды по названию

Популярные бренды