Thermo Scientific Orion AQUAfast AQ3010 Скачать руководство пользователя | Manualshive

Страница: 19 / 39

background image

Thermo Scientific Orion AQUAfast AQ3010 Turbidity Meter User Guide

15

Chapter 3

Turbidity Measurement

The AQ3010 waterproof turbidity meter allows you to measure the

turbidity of a grab sample . The turbidity is reported in Nephelometric

Turbidity Units (NTU) . Readings above 1000 NTU are outside the

range of this instrument .

Note:

Before switching on the AQ3010 turbidity meter, a sample vial

must be placed in the sample well . You can use any of the calibration

standards for this purpose .

The instrument includes a light shield cover to keep stray light from

changing the calibration and sample measurement readings . In many

environments, the light shield is not required . The vial cap keeps stray

light from entering the sample well, saving you many steps and reducing

analysis time .

When the

ON/OFF

key is pressed to switch on the meter, it goes through

the power-up sequence as shown in

Figure 8

.

General

nformation

Figure

Power-up Sequence

CAL 13 CAL 24

mg/l
N TU
ppm
%pH

TAvg

NTU

"-Rd-” flashes about 10

times indicating that the

meter goes to

m easurement mode.

A reading is valid only if you have placed a

vial or any of the calibration standards

provided into the sam ple well.Otherwise

the reading has no meaning or an error

message "Err 8" appears.

Instrument Off

Place a sam ple vial or any of the

calibration standards provided into

the sam ple well of the meter, before

switch on.

X.x

“X.X” is software revision

number

Place light shield cap over vial.

«
...
17
18
19
20
21
...
»

Содержание Orion AQUAfast AQ3010








































Отзывы:

Нет отзывов

Похожие инструкции для Orion AQUAfast AQ3010

Бренд: Cablescan Страницы: 58

Goldmann AT 870

Бренд: Haag-Streit Страницы: 20

Бренд: Hanna Instruments Страницы: 2

Бренд: Hanna Instruments Страницы: 2

Бренд: Hanna Instruments Страницы: 2

Бренд: Hanna Instruments Страницы: 4

Бренд: Hanna Instruments Страницы: 2

Бренд: MADDALENA Страницы: 4

Бренд: Macnaught Страницы: 4

Бренд: Yamaha Страницы: 72

Бренд: Yamaha Страницы: 5

Бренд: Yamaha Страницы: 16

Бренд: Yamaha Страницы: 8

Бренд: Yamaha Страницы: 7

Бренд: Yamaha Страницы: 60

GranTouch Digital Grand Piano

Бренд: Yamaha Страницы: 19

Бренд: Yamaha Страницы: 44

Бренд: Yamaha Страницы: 29

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды