Thermo Scientific Orion AQUAfast AQ3010 Скачать руководство пользователя

Страница: 27 / 39

Thermo Scientific Orion AQUAfast AQ3010 Turbidity Meter User Guide

Chapter 5

Customer Services

The AQ3010 turbidity meter routinely performs self-diagnostics and will

automatically generate messages to provide you with specific diagnostic

information . These messages are for your use and do not indicate a

reduction in the performance of the instrument or a failure of any

component in the instrument, unless otherwise stated in this list .

LCD
Message

Description

Corrective Actions

ERR 1

Calibration error – the meter is

unable to recognize the 800 NTU

calibration standard.

Use the correct 800 NTU

calibration standard. Pour fresh

standard into a clean vial and retry

the calibration. Verify that the

standard has not expired.

ERR 2

Calibration error – the meter is

unable to recognize the 100 NTU

calibration standard.

Use the correct 100 NTU

calibration standard. Pour fresh

standard into a clean vial and retry

the calibration. Verify that the

standard has not expired.

ERR 3

Calibration error – the meter is

unable to recognize the 20.0 NTU

calibration standard.

Use the correct 20.0 NTU

calibration standard. Pour fresh

standard into a clean vial and retry

the calibration. Verify that the

standard has not expired.

ERR 4

Calibration error – the meter is

unable to recognize the 0.02 NTU

calibration standard.

Use the correct 0.02 NTU

calibration standard. Pour fresh

standard into a clean vial and retry

the calibration. Verify that the

standard has not expired.

ERR 5

Calibration error – there is not

sufficient signal to achieve the

appropriate resolution in the 0 to

1000 NTU range.

Pour fresh standard into a clean

vial and retry the calibration with

all four standards. Verify that the

standards have not expired.

ERR 6

General calibration failure – there

is not sufficient signal to achieve

the appropriate resolution in the 0

to 100 NTU range.

Pour fresh standard into a clean

vial and retry the calibration with

all four standards. Verify that the

standards have not expired.

ERR 7

General calibration failure – there

is not sufficient signal to achieve

the appropriate resolution in the 0

to 20 NTU range.

Pour fresh standard into a clean

vial and retry the calibration with

all four standards. Verify that the

standards have not expired.

Troubleshooting

Guide

Содержание Orion AQUAfast AQ3010








































Результаты поиска

Содержание Orion AQUAfast AQ3010

Отзывы:

Похожие инструкции для Orion AQUAfast AQ3010

Бренды по названию

Популярные бренды

Thermo Scientific Orion AQUAfast AQ3010, Руководство пользователя

Результаты поиска

Содержание Orion AQUAfast AQ3010

Отзывы:

Похожие инструкции для Orion AQUAfast AQ3010

Бренды по названию

Популярные бренды