manualshive.com logo in svg

Thermo Scientific Orion 310, Инструкция по эксплуатации

Поделиться
Скачать
Thermo Scientific Orion 310 Скачать руководство пользователя страница 71

67

PerpHecT

®

 Orion 310, 320, 330 Instruction Manual

Notice of Compliance

Chapter XXIV

Notice of Compliance

WARNING:

 This meter may radiate radio

frequency energy and if not installed and used
properly, that is in strict accordance with the
manufacturer's instructions, may cause interference
to radio communications. It has been tested and
found to comply with the limits for a Class A
computing device pursuant to Subpart J of Part 15
of FCC Rules, which are designed to provide
reasonable protection against such interference in a
commercial environment. Operation of the meter in
a residential area may cause interference in which
case the user at his own expense will be required to
take whatever measures may be required to correct
the interference.

NOTE:

 To meet or exceed FCC regulations the

Orion-supplied line converters must be used.

This digital apparatus does not exceed the Class A limits for radio noise
emissions from digital apparatus set out in the Radio Interference
Regulations of the Canadian Department of Communications.

Le présent appareil numérique n’ émet pas de bruits radioélectriques
dépassant les limites applicables aux appareils numériques (de la class A)
prescrites dans le Règlement sur le brouillage radioélectrique édicté par le
ministère des Communications du Canada.”

Содержание Orion 310


















































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды