manualshive.com logo in svg

Thermo Scientific Orion 310, Инструкция по эксплуатации

Поделиться
Скачать
Thermo Scientific Orion 310 Скачать руководство пользователя страница 13

9

PerpHecT

®

 Orion 310, 320, 330 Instruction Manual

Chapter IV

Using the Orion 310

A.  Power-Up

Plug meter into an approved wall outlet via the power line adaptor. The
entire display (all annunciators) will be displayed for 2 seconds. Once all
power-up procedures have been completed, the meter automatically
advances to measure mode.

NOTE:

  If this is the first time that the meter has

been powered up, it is recommended that the Self-
Test Procedure be performed before using the meter
for measurements.

B.  Meter Self-Test Procedure

It is recommended that this procedure be performed when the meter is
operated for the first time or any time that operational problems arise.

For a description of the diagnostic tests, see Chapter XVIII Self-Test
Definitions pg 53.
This procedure verifies the proper operation of the PerpHecT meters.

Self-test:

1. Attach shorting cap to electrode BNC input.

2. Plug line adapter (Orion 020125) securely into meter Line Adapter

Input then into an appropriate wall outlet while pressing the YES
key (hold down for 3 seconds) to start the self-test.  The meter will
automatically perform seven diagnostic tests.

3. When “0” appears in the display field, press each key once.

A numeric digit will be displayed upon each keypress.

4. After the self-test is completed, the meter will automatically go to

MEASURE mode.

5. If any problems are found during the self-test see Operator

Assistance Codes, page 55.

Using the Orion 310

Содержание Orion 310


















































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды