Thermador PRG486JDG/01 Скачать руководство пользователя страница 91 | Manualshive

Страница: 91 / 91

Thermador PRG486JDG/01 Скачать руководство пользователя страница 91

Service Manual for the Thermador Pro Grand Next Generation 48-Inch Natural Gas and LP Gas Ranges, Models:

PRG486JDG/01, PRL486JDG/01

58300000159722_ARA_EN_D

Page 92 of 92

8 CLEAN-UP

After you have finished servicing an appliance, clean up grease,
fingerprints, and other residue that is present as the result of servicing
the appliance. Refer to the Care and Use Manual for clean-up
information.

Clean-up Hazards

■

Don’t allow any cleaning or polishing solutions/compounds,

disinfectants or bleaches to remain in contact with the stainless
steel surfaces for long periods, or after clean-up. These may
contain chemicals or materials which could release harmful
inhalants or may damage the appliance. After cleaning or
polishing, always rinse the cleaning/polishing materials with clear
water and wipe dry with a clean, soft, non-abrasive cloth.

■

Clean the range with caution. Do not use flammable cleaners to

clean the range. Avoid steam burns; do not use a wet sponge or
cloth to clean the range while it is hot. Do not use any type of
aerosol cleaner on or around the rangetop when hot. Some
cleaners produce noxious fumes if applied to a hot surface. Follow
directions provided by the cleaner manufacturer.

9 ADDITIONAL RESOURCES

9.1 QuickFinder

For further information, please refer to the following documents on
QuickFinder at ■

Installation Manual

Care and Use Manual

In addition, the following may be available on QuickFinder:

■

Product Information screen (includes technical specification for the

appliance)

■

Gas Information (Repair Instruction)

■

Wiring Diagram

■

Accessories List

■

Spare Parts Notes/Information (Technical Service Bulletins, and

Technical Information Bulletins)

■

Exploded View Drawing

■

Parts List

NOTE:

Not all service parts are shown on the QuickFinder

exploded views; review the Parts List for additional information.

9.2 Technical Support

For authorized servicers, additional assistance is available by
contacting our Technical Support Team at (800) 444-9091 between
5:00 am and 5:00 pm, Monday–Friday, Pacific Standard time.

«
...
89
90
91

Содержание PRG486JDG/01




























































































Отзывы:

Нет отзывов