manualshive.com logo in svg

Thermador PRG486JDG/01, Руководство по обслуживанию, Страница: 26 / 91

Поделиться
Скачать
Thermador PRG486JDG/01 Скачать руководство пользователя страница 26

Service Manual for the Thermador Pro Grand Next Generation 48-Inch Natural Gas and LP Gas Ranges, Models: 

PRG486JDG/01, PRL486JDG/01

 

 

 

 

 

 

 

 

 

 

58300000159722_ARA_EN_D

 

 

 

 

 

 

 

      Page 27 of 92

 

6.4  Griddle / Grill Removal and Replacement 

 The griddle / grill removal requires access from the back and the 

top of the range. 

The griddle / grill preheat time (the time from when the griddle is 
turned on until the preheat light goes off) will vary according to 
ambient (room) temperature and the level of electrical service. 
Preheating griddle to 350° F may take approximately 10–14 minutes. 

Be sure to check QuickFinder for relevant information, documentation, 
and the correct part number when replacing this component. 

 

Griddle / Grill Hazard 

The griddle / grill plate must always be correctly in place when it is on. 

1.  Follow all safety precautions and steps in 

Preparing the Range for 

Servicing,

 page 

22.

 

2.  Complete steps for 

Accessing Components under the Maintop, 

page

 22.

 

3.  Remove the grill / griddle plate and grease tray (see Figure 22). 

 

Figure 22: Griddle Plate and Grease Tray 

1 

Grease tray  

2 

Griddle plate 

4.  Remove the backguard (see 

Backguard Removal and 

Replacement, 

page

 61

 

5.  At the back of the range, disconnect the 1/4 inch spade 

connectors of both right and left element wires. 

6.  Carefully remove the bulb from the fixed retaining bracket (see 

Figure 23). 

NOTE: 

After removing the thermostat bulb from retaining bracket, 

don’t push the bulb through the receptacle in the element tray yet. 

7.  Disconnect the 1/4 inch spade connectors of both right and left 

element wires. You may have to pull the element wires out a bit to 
access the connectors. While doing this, be careful not to damage 
the element wires. 

 

Figure 23: Removing Thermostat Bulb from Retaining Bracket 

1 

Retaining bracket 

2 

Thermostat bulb 

3 

Receptacle for removing bulb 

Содержание PRG486JDG/01




























































































Отзывы:

Нет отзывов