Thermador PRG486JDG/01 Скачать руководство пользователя страница 8 | Manualshive

Страница: 8 / 91

Thermador PRG486JDG/01 Скачать руководство пользователя страница 8

Service Manual for the Thermador Pro Grand Next Generation 48-Inch Natural Gas and LP Gas Ranges, Models:

PRG486JDG/01, PRL486JDG/01

58300000159722_ARA_EN_D

Page 9 of 92

■

Clean the range with caution. Do not use flammable cleaners to

clean the range. Avoid steam burns; do not use a wet sponge or
cloth to clean the range while it is hot. Do not use any type of
aerosol cleaner on or around the rangetop when hot. Some
cleaners produce noxious fumes if applied to a hot surface. Follow
directions provided by the cleaner manufacturer.

Fiberglass Insulation

Wear gloves when handling fiberglass insulation.

Oven Door, Oven Accessories and Oven Gasket

■

Use caution when opening the oven door during or immediately

after operation. Stand to the side of the oven when opening an
oven door to allow hot air to escape. Keep face well away from the
open door to avoid injury.

■

Before self-cleaning an oven, remove the broiler pan, oven racks,

any utensils, as well as excessive spillage

■

Do not clean, rub, damage, move, or remove the door gasket, as it

is essential for providing a tight seal during oven operation. If the
gasket becomes worn or excessively soiled with food particles,
replace the gasket.

Prior to Returning Appliance to Service

Prior to returning the appliance to service, make sure that:

■

All electrical connections are correct and secure

■

All safety grounds (internal and external) are correctly and

securely connected

■

All gas connections are secure and have been leak tested using a

gas leak detector or bubble test.

■

All panels and components are properly and securely

reassembled

Backguard Ventilation

■

To ensure sufficient airflow for proper oven performance, do not

block or obstruct the vents located on the backguard (high
backguard, lowback, or island trim).

■

Backguard vents and surrounding areas are hot. Do not place

plastic, other heat-sensitive items, or flammable / combustible
materials on or near the backguard vents, as these areas could
melt or ignite.

■

Don’t touch or clean the backguard vent area while the appliance

is on, nor for several minutes after the appliance is turned off, to
prevent burning yourself.

«
...
6
7
8
9
10
...
»

Содержание PRG486JDG/01




























































































Отзывы:

Нет отзывов