Thermador PRG486JDG/01 Скачать руководство пользователя страница 89

Страница: 89 / 91

Service Manual for the Thermador Pro Grand Next Generation 48-Inch Natural Gas and LP Gas Ranges, Models:

PRG486JDG/01, PRL486JDG/01

58300000159722_ARA_EN_D

Page 90 of 92

5. At the base of the door assembly, gently lift the inner glass panel

upward slightly while removing the two lower retaining brackets
that are positioned around the door hinges (see Figure 145).

6. Gently pull the inner glass panel out in the direction of the door

base, at a slight angle. Be careful that the upper bracket doesn’t
damage the glass panel during removal (see Figure 145).

Figure 145: Door Components (Large Door Shown)

Screw to remove (1 on each side of door)

Upper bracket (1)

Inner glass panel

Lower retaining brackets (1 on each side of door)

6.9.11

Door Gasket Removal and Replacement

Be sure to check QuickFinder for relevant information,

documentation, and the correct part number when replacing this
component.

1. Follow all safety precautions and steps in

Preparing the Range for

Servicing,

page

22.

2. Remove oven door (see

Oven Door Removal, Installation,

page

70).

3. Starting from one end of the gasket while carefully working your

way to the other end, gently pull the gasket clips out of the
receptacles on the oven frame (see Figure 146).

4. After replacing the gasket, check to make sure the door is

positioned correctly, and closes with a tight fit.

Figure 146: Gasket on Typical Oven Cavity

Содержание PRG486JDG/01




























































































Результаты поиска

Содержание PRG486JDG/01

Отзывы:

Thermador PRG486JDG/01, Руководство по обслуживанию, Страница: 89 / 91

Результаты поиска

Содержание PRG486JDG/01

Отзывы: