Theben PlanoCentro A-KNX Скачать руководство пользователя страница 32

Страница: 32 / 50

Page 32 of 50

KNX presence detector PlanoCentro A-KNX

Test modes

The PlanoCentro has two test modes.

•

Test mode presence, page 32 chapter 6.2.1

•

Test mode light, page 32 chapter 6.2.2

The test modes can only be started if the device is switched on.

6.2.1 Test presence

The test presence serves to test presence detection and parallel connection.

Activation

Test presence "On" with the SendoPro 868-A management remote control

via bus object 33

The test mode presence can be activated at anytime.

End

With subsequent restart:

Test presence "Off" command with the SendoPro 868-A management remote control

Power failure and power up

Automatically according to the time set with the ETS

via bus object 33

Without restart:

Activation of test light with SendoPro 868-A management remote control

LED display
Status channels

Description

With movement (LED on) the A channels light and H channels presence close.

Off

When the room is unoccupied (LED off) both channels open after 15 seconds.

Test response

Deactivate brightness measurement, light output does not react to brightness

The detector reacts as in fully automatic function mode even if semi-automatic is set.

The control type changes to switching if the control type is set to constant light control. The light is not controlled.

Light «On» with movement; light «Off» with absence of movement.

A channel light and H channel presence have a fixed switch-off delay of 15 seconds.

Room monitoring reacts unchanged as in normal operating mode.

Switch-on delay H channel and J presence is set to 0 seconds.

Commands and other parameters

The following commands are possible with the management remote control in test mode presence

End test presence

Activate test light

Change detection sensitivity

Change reducing sensitivity with room monitoring

The selected detection sensitivity (1–5), see page 16, is unchanged on activation of test presence. Sensitivity can be adjusted during the test.
The presence detector performs a reset after the end of the test mode.

6.2.2 Test light

The test light serves to monitor the brightness level (brightness threshold).

Activation

Test light "On" with the SendoPro 868-A management remote control

via bus object 34

Test light can be activated at anytime.

End

With subsequent restart:

Test light "Off" with the SendoPro 868-A management remote control

Power failure and power up

Automatically according to the time set with the ETS

via bus object 34

Without restart:

Activation of test presence with SendoPro 868-A management remote control

Содержание PlanoCentro A-KNX



















































Результаты поиска

Содержание PlanoCentro A-KNX

Отзывы:

Похожие инструкции для PlanoCentro A-KNX

Бренды по названию

Популярные бренды

Theben PlanoCentro A-KNX, Руководство по применению

Результаты поиска

Содержание PlanoCentro A-KNX

Отзывы:

Похожие инструкции для PlanoCentro A-KNX

Бренды по названию

Популярные бренды