manualshive.com logo in svg

Textron Bell 206A Series, Руководство по обслуживанию


Поделиться
Скачать
background image

BHT-206A/B-SERIES-MM-1

5-00-00

30 APR 2013 Rev. 14

Page 189

Export Classification C, ECCN EAR99

BHT-206A/B-M&O,
BHT206B3-CR&O

TRANSMISSION ASSEMBLY

1.

Remove the transmission input pinion and triplex bearing.

2.

Inspect the following gear teeth for scoring and other

mechanical damage.

a.

Input pinion gear

b.

Main input driven bevel gear

3.

If any damage suspected to be related to the compressor

stall or surge is found, make an entry on the Historical Service
Record, and attach a tag on the transmission assembly and
write “THIS COMPONENT WAS REMOVED FROM SERVICE
BECAUSE OF A COMPRESSOR STALL/SURGE”. Send the
component to a Bell Helicopter Textron approved facility for
overhaul. 

4.

If no defects were detected on the gears, the transmission

assembly is serviceable. 

BHT206B3-CR&O

TAIL ROTOR GEARBOX

1.

Remove the tail rotor gearbox input pinion.

2.

Inspect the following gear teeth for scoring and other

mechanical damage.

a.

Input pinion gear

b.

Spiral bevel gear

3.

If any damage suspected to be related to the compressor

stall or surge is found, make an entry on the Historical Service
Record, and attach a tag on the tail rotor gearbox and write
“THIS COMPONENT WAS REMOVED FROM SERVICE
BECAUSE OF A COMPRESSOR STALL/SURGE”. Send the
tail rotor gearbox to a Bell Helicopter Textron approved facility
for overhaul.

4.

If no defects were detected on the gears, the tail rotor

gearbox is serviceable. 

CONDITIONAL INSPECTIONS

5-57.

ENGINE COMPRESSOR STALL OR SURGE (CONT)

DATA REFERENCE

INSPECTION TASK DESCRIPTION

INITIAL

MECH      OTHER

Содержание Bell 206A Series











































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Bell 206A Series

Eachine E150 User Manual preview
E150
Бренд: Eachine Страницы: 8
GAME OF BRICKS 21325 Instruction Manual preview
21325
Бренд: GAME OF BRICKS Страницы: 30
roco 1116 OBB Operating Manual preview
1116 OBB
Бренд: roco Страницы: 8
Radica Games RC71103 Instruction Manual preview
RC71103
Бренд: Radica Games Страницы: 2
Trix 12343 Operating Instructions Manual preview
12343
Бренд: Trix Страницы: 12
Eduard Mi-24V Hind armament set Assembly Instructions preview
Mi-24V Hind armament set
Бренд: Eduard Страницы: 2
Horizon Hobby Delta Ray RTF Instruction Manual preview
Delta Ray RTF
Бренд: Horizon Hobby Страницы: 18
Lansay Peche aux Canards Instructions For Use preview
Peche aux Canards
Бренд: Lansay Страницы: 2
marklin 29130 User Manual preview
29130
Бренд: marklin Страницы: 20
Mega Construx HALO DPJ91 Manual preview
HALO DPJ91
Бренд: Mega Construx Страницы: 32
Saitek Mephisto CT03 Instructions Manual preview
Mephisto CT03
Бренд: Saitek Страницы: 51
Trix 22134 Manual preview
22134
Бренд: Trix Страницы: 28
The Drone Warehouse JJR/C H20 User Manual preview
JJR/C H20
Бренд: The Drone Warehouse Страницы: 9
Meccano SPACECHAOS DARK PIRATES 5104 Instructions Manual preview
SPACECHAOS DARK PIRATES 5104
Бренд: Meccano Страницы: 24
VTech Mooove n Count Cow User Manual preview
Mooove n Count Cow
Бренд: VTech Страницы: 9
Eduard Panther Ausf. D Zimmerit Vertical Quick Start Manual preview
Panther Ausf. D Zimmerit Vertical
Бренд: Eduard Страницы: 4
Hobbytrain SB Series Manual preview
SB Series
Бренд: Hobbytrain Страницы: 5
REVELL Destroyer H.M.S. Campbeltown Assembly Manual preview
Destroyer H.M.S. Campbeltown
Бренд: REVELL Страницы: 10

Бренды по названию

Популярные бренды

Загрузить еще бренды