manualshive.com logo in svg

Textron Bell 206A Series, Руководство по обслуживанию


Поделиться
Скачать
background image

BHT-206A/B-SERIES-MM-1

5-00-00
Page 188

Rev. 14 30 APR 2013

Export Classification C, ECCN EAR99

SPECIAL INSPECTION

After 25 hours of operation, examine chip detectors of
transmission, freewheel assembly, and tail rotor gearbox. If the
chip detector shows signs of metal particles, perform a
serviceability check. Components that fail the serviceability
check shall be removed. Make an entry on the applicable
components Historical Service Record, and attach a tag and
write “THIS COMPONENT WAS REMOVED FROM SERVICE
BECAUSE OF A COMPRESSOR STALL/SURGE”. Send the
component to a Bell Helicopter Textron approved facility for
overhaul.

PART III: INSPECTION FOR COMPRESSOR STALL 

OR SURGE WITH NOTICEABLE YAW

CAUTION

WHEN A COMPRESSOR STALL OR SURGE WITH
NOTICEABLE YAW HAS OCCURRED, DISCARD
ALL TAIL ROTOR BONDED DRIVESHAFTS.

BHT-206B3-CR&O

ENGINE-TO-TRANSMISSION DRIVESHAFT

1.

Remove and disassemble the engine-to-transmission

driveshaft for condition.

2.

Inspect the inner and outer coupling teeth splines for

damage.

3.

If any damage suspected to be related to the compressor

stall or surge is found, make an entry on the Historical Service
Record, and attach a tag on the driveshaft and write “THIS
COMPONENT WAS REMOVED FROM SERVICE BECAUSE
OF A COMPRESSOR STALL/SURGE”. Send the
engine-to-transmission driveshaft to a Bell Helicopter Textron
approved facility for overhaul.

4.

If no defects were detected, return the

engine-to-transmission driveshaft to service.

CONDITIONAL INSPECTIONS

5-57.

ENGINE COMPRESSOR STALL OR SURGE (CONT)

DATA REFERENCE

INSPECTION TASK DESCRIPTION

INITIAL

MECH      OTHER

Содержание Bell 206A Series











































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Bell 206A Series

Badger Basket 66107 Assembly And Use Instructions preview
66107
Бренд: Badger Basket Страницы: 3
Badger Basket 15405 Manual preview
15405
Бренд: Badger Basket Страницы: 4
Badger Basket 12030 Assembly Instructions Manual preview
12030
Бренд: Badger Basket Страницы: 10
Badger Basket 12022 Assembly And Use Instructions preview
12022
Бренд: Badger Basket Страницы: 6
BARCLONE Antares Instruction Manual preview
Antares
Бренд: BARCLONE Страницы: 14
Eduard M-2A2 Bradley IFV Quick Start Manual preview
M-2A2 Bradley IFV
Бренд: Eduard Страницы: 6
Tronhelicopters Tron 5.5 Manual preview
Tron 5.5
Бренд: Tronhelicopters Страницы: 43
REVELL Steaman Aerobatic Biplane Assembly Instructions Manual preview
Steaman Aerobatic Biplane
Бренд: REVELL Страницы: 12
Faller Val Tuoi Viaduct-Set Assembly Instructions Manual preview
Val Tuoi Viaduct-Set
Бренд: Faller Страницы: 8
Stevens AeroModel SHAFT25e Instruction Manual preview
SHAFT25e
Бренд: Stevens AeroModel Страницы: 29
Fisher-Price 77770 Owner'S Manual With Assembly Instructions preview
77770
Бренд: Fisher-Price Страницы: 32
Mega Bloks Barbie Babysitter Manual preview
Barbie Babysitter
Бренд: Mega Bloks Страницы: 28
Propel RC LASER FORCE User Manual preview
LASER FORCE
Бренд: Propel RC Страницы: 4
Eduard Hummel exterior Assembly Instructions preview
Hummel exterior
Бренд: Eduard Страницы: 4
MODSTER 282310 User Manual preview
282310
Бренд: MODSTER Страницы: 38
Zapf Creation Baby Annabell 916236 Manual preview
Baby Annabell 916236
Бренд: Zapf Creation Страницы: 2
E-FLITE F86 Sabre 15DF Assembly Manual preview
F86 Sabre 15DF
Бренд: E-FLITE Страницы: 44
Tabletop Scenics Fantasy Bowl Stadium Short Tribune Construction Manual preview
Fantasy Bowl Stadium Short Tribune
Бренд: Tabletop Scenics Страницы: 5

Бренды по названию

Популярные бренды

Загрузить еще бренды