manualshive.com logo in svg

Textron Bell 206A Series, Руководство по обслуживанию


Поделиться
Скачать
background image

BHT-206A/B-SERIES-MM-1

5-00-00

30 APR 2013 Rev. 14

Page 185

Export Classification C, ECCN EAR99

NOTE

Removal or dismantling of components is not
required while performing the following inspection.

PART II: INSPECTION FOR COMPRESSOR STALL OR 

SURGE WITHOUT NOTICEABLE YAW

Chapter 63 and 
Chapter 65

DRIVE SYSTEM

1.

Examine the chip detectors of the transmission, freewheel

assembly, and the tail rotor gearbox. If the chip detector shows
signs of metal particles, perform a serviceability check.
Components that fail the serviceability check shall be removed.
Make an entry on the applicable components Historical Service
Record, and attach a tag and write “THIS COMPONENT WAS
REMOVED FROM SERVICE BECAUSE OF A COMPRESSOR
STALL/SURGE”. Send the component to an approved facility for
overhaul. 

2.

Examine the tail rotor driveshafts for condition and security

of attachment.

3.

Examine the tail rotor disc pack couplings for cracks or

gapping greater than 0.015 inch (0.38 mm).

4.

Examine the tail rotor steel driveshaft and adapters for

structural failure or distortion exceeding specified limits.

5.

Examine the bondlines between adapters and tube of the

long tail rotor driveshaft for any evidence of cracks and voids, if
installed.

6.

Examine the bondlines on all bonded tail rotor driveshaft

adapters for any evidence of cracks and voids, if installed.

7.

If any defect is detected in step 2 through step 6, all

bonded tail rotor driveshafts shall be considered unserviceable
and scrapped.

8.

Examine the tail rotor driveshaft segments having riveted

adapters for condition, if installed.

CONDITIONAL INSPECTIONS

5-57.

ENGINE COMPRESSOR STALL OR SURGE (CONT)

DATA REFERENCE

INSPECTION TASK DESCRIPTION

INITIAL

MECH      OTHER

Содержание Bell 206A Series











































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Bell 206A Series

Laser Pegs GI670B User Manual preview
GI670B
Бренд: Laser Pegs Страницы: 6
Laser Pegs G870B Model Instructions preview
G870B
Бренд: Laser Pegs Страницы: 4
Laser Pegs G1270B Model Instructions preview
G1270B
Бренд: Laser Pegs Страницы: 3
Laser Pegs Eagle ZD 140B Manual preview
Eagle ZD 140B
Бренд: Laser Pegs Страницы: 17
Laser Pegs Assault Helicopter C1200 Instruction Manual preview
Assault Helicopter C1200
Бренд: Laser Pegs Страницы: 3
Laser Pegs ALL TERRAIN ROVER ZD 110B Assembly Manual preview
ALL TERRAIN ROVER ZD 110B
Бренд: Laser Pegs Страницы: 16
Laser Pegs 1270 Instructions For Use preview
1270
Бренд: Laser Pegs Страницы: 2
Laser Pegs National Geographic Oceans Model Instructions preview
National Geographic Oceans
Бренд: Laser Pegs Страницы: 2
Radica Games 74004 Instruction Manual preview
74004
Бренд: Radica Games Страницы: 2
Radica Games 75029 Instruction Manual preview
75029
Бренд: Radica Games Страницы: 2
PAU 150cc Extra 300SP ARF Instruction Manual preview
150cc Extra 300SP ARF
Бренд: PAU Страницы: 19
Radio Shack Rockin' PT Cruiser Owner'S Manual preview
Rockin' PT Cruiser
Бренд: Radio Shack Страницы: 4
Fisher-Price L5198 Bubble Mower Consumer Information preview
L5198 Bubble Mower
Бренд: Fisher-Price Страницы: 28
GAUGEMASTER Fordhampton Garden center Manual preview
Fordhampton Garden center
Бренд: GAUGEMASTER Страницы: 4
LeapFrog 100 English-Chinese Words Book Parents' Manual preview
100 English-Chinese Words Book
Бренд: LeapFrog Страницы: 10
Faller BLACK FOREST MILL Quick Start Manual preview
BLACK FOREST MILL
Бренд: Faller Страницы: 8
PARKZONE Extra 300 PNP Instruction Manual preview
Extra 300 PNP
Бренд: PARKZONE Страницы: 22
Fisher-Price P9513 Instructions preview
P9513
Бренд: Fisher-Price Страницы: 4

Бренды по названию

Популярные бренды

Загрузить еще бренды