manualshive.com logo in svg

Textron Bell 206A Series, Руководство по обслуживанию


Поделиться
Скачать
background image

BHT-206A/B-SERIES-MM-1

5-00-00
Page 186

Rev. 14 30 APR 2013

Export Classification C, ECCN EAR99

9.

Examine the oil cooler shaft and forward short shaft for

condition.

10.

Examine the engine-to-transmission driveshaft for

condition. 

11.

If no defects were detected that may have been caused by

the compressor stall or surge, all drivetrain components are
serviceable.

Chapter 62 and 
Chapter 67

ROTATING CONTROL SYSTEM

1.

Examine the swashplate and support assembly,

swashplate drive components, the tail rotor pitch change
mechanism, and all rotating controls (main and tail). Replace
any unserviceable parts as necessary.

Chapter 64

TAIL ROTOR HUB AND BLADES

1.

Examine the tail rotor hub assembly for condition. If any

damage suspected to be related to the compressor stall or
surge is found, remove the tail rotor hub assembly. Make an
entry on the Historical Service Record, and attach a tag on the
tail rotor hub assembly and write "THIS COMPONENT WAS
REMOVED FROM SERVICE BECAUSE OF A COMPRESSOR
STALL/ SURGE". Send the hub to an approved facility for
overhaul.

2.

Examine the tail rotor blades for condition. If any damage

suspected to be related to the compressor stall or surge is
found, remove the tail rotor blades. Make an entry on the
Historical Service Record, and attach a tag on the tail rotor
blade(s) and write "THIS BLADE WAS REMOVED FROM
SERVICE BECAUSE OF A COMPRESSOR STALL/SURGE".
Send the tail rotor blades assembly to a Bell Helicopter Textron
approved rotor blade repair facility for further inspection and
repair.

3.

Examine the tail rotor blade bolts for security of

attachment. If damage suspected to be related to the
compressor stall or surge is found, discard them.

CONDITIONAL INSPECTIONS

5-57.

ENGINE COMPRESSOR STALL OR SURGE (CONT)

DATA REFERENCE

INSPECTION TASK DESCRIPTION

INITIAL

MECH      OTHER

Содержание Bell 206A Series











































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Bell 206A Series

Old School Model Works GHOST Construction Manual preview
GHOST
Бренд: Old School Model Works Страницы: 26
Fisher-Price CWT61 Manual preview
CWT61
Бренд: Fisher-Price Страницы: 2
Mega Bloks SKYLANDERS GIANTS SPYRO 95418 Manual preview
SKYLANDERS GIANTS SPYRO 95418
Бренд: Mega Bloks Страницы: 16
K'Nex Education RENEWABLE ENERGY WATER POWERED... Manual preview
Education RENEWABLE ENERGY WATER POWERED...
Бренд: K'Nex Страницы: 20
PARKZONE Extra 300 PNP Instruction Manual preview
Extra 300 PNP
Бренд: PARKZONE Страницы: 22
Fisher-Price P9513 Instructions preview
P9513
Бренд: Fisher-Price Страницы: 4
Lionel The Lone Ranger Owner'S Manual preview
The Lone Ranger
Бренд: Lionel Страницы: 24
GAUGEMASTER Structures Fordhampton Bridge Assembly Instructions preview
Structures Fordhampton Bridge
Бренд: GAUGEMASTER Страницы: 4
LEGO 70313 Manual preview
70313
Бренд: LEGO Страницы: 63
Rolly Toys Rolly FarmTrac 610.000.810.00 Manual preview
Rolly FarmTrac 610.000.810.00
Бренд: Rolly Toys Страницы: 5
LEGO 75882 Assembly preview
75882
Бренд: LEGO Страницы: 84
Horizon Hobby Night Vapor BNF Instruction Manual preview
Night Vapor BNF
Бренд: Horizon Hobby Страницы: 13
Hornby 2P Class Manual preview
2P Class
Бренд: Hornby Страницы: 2
K'Nex Ferris Wheel Manual preview
Ferris Wheel
Бренд: K'Nex Страницы: 16
VTech Toot-Toot Drivers Airport Instruction Manual preview
Toot-Toot Drivers Airport
Бренд: VTech Страницы: 19
Eduard F4U-1D interior 1/32 Manual preview
F4U-1D interior 1/32
Бренд: Eduard Страницы: 4
STUDIO27 TEAM LOTUS 91 Assembly Instructions preview
TEAM LOTUS 91
Бренд: STUDIO27 Страницы: 4
m2model Discovery micro Assembly Instructions preview
Discovery micro
Бренд: m2model Страницы: 3

Бренды по названию

Популярные бренды

Загрузить еще бренды