Texas Instruments TMS320C6670 Скачать руководство пользователя страница 32

Страница: 32 / 226

Device Overview

SPRS689D—March 2012

Multicore Fixed and Floating-Point System-on-Chip

TMS320C6670

www.ti.com

Submit Documentation Feedback

2.4.2.3 Ethernet (SGMII) Boot Device Configuration

2.4.2.4 PCI Boot Device Configuration

Additional device configuration is provided in the PCI bits in the DEVSTAT register.

Figure 2-5

Ethernet (SGMII) Device Configuration Fields

SerDes Clock Mult

Ext connection

Dev ID

Table 2-6

Ethernet (SGMII) Configuration Field Descriptions

Bit

Field

Description

9-8

SerDes clock mult

SGMII SerDes input clock. The output frequency of the PLL must be 1.25 GBs.

0 = ×8

for input clock of 156.25 MHz

1 = ×5 for input clock of 250 MHz
2 = ×4 for input clock of 312.5 MHz
3 = Reserved

7-6

Ext connection

External connection mode

0 = MAC to MAC connection, master with auto negotiation
1 = MAC to MAC connection, slave, and MAC to PHY
2 = MAC to MAC, forced link
3 = MAC to fiber connection

5-3

Device ID

This value can range from 0 to 7 and is used in the device ID field of the Ethernet-ready frame.

End of Table 2-6

Figure 2-6

PCI Device Configuration Fields

Reserved

BAR Config

Reserved

Table 2-7

PCI Device Configuration Field Descriptions

Bit

Field

Description

Reserved

8-5

Bar Config

PCIe BAR registers configuration

This value can range from 0 to 0xf. See

Table 2-8

4-3

Reserved

End of Table 2-7

Содержание TMS320C6670


































































































































































































































Результаты поиска

Содержание TMS320C6670

Отзывы:

Похожие инструкции для TMS320C6670

Бренды по названию

Популярные бренды

Texas Instruments TMS320C6670, Руководство по данным

Результаты поиска

Содержание TMS320C6670

Отзывы:

Похожие инструкции для TMS320C6670

Бренды по названию

Популярные бренды