manualshive.com logo in svg

Texas Instruments LDC3114, Руководство пользователя

Поделиться
Скачать
Texas Instruments LDC3114 Скачать руководство пользователя страница 15

7.4.2 Low Power Mode

When the LPWRB input pin is set to ground, only the low-power-enabled channels are active. Each channel can 
be enabled independently to operate in Low Power Mode through 

Register EN (Address 0x0C)

. For a channel 

to operate in the Low Power Mode, both the LPEN

n

 and EN

n

 bits (

n

 is the channel index) must be set to 1. The 

Low Power Mode allows for energy-saving monitoring of button activity. In this mode, the device is in an inactive 
power-saving  state  for  the  majority  of  the  time.  Lower  scan  rates  correspond  to  lower  current  consumption. 
In  addition,  the  individual  button  sampling  window  should  be  set  to  the  lowest  effective  setting  (this  is  system 
dependent,  but  typically  0.8  ms  to  1  ms).  For  the  electrical  specification  of  the  configurable  Low  Power  Mode 
Scan Rate, refer to the 

Electrical Characteristics

 table.

If  a  channel  is  operational  in  both  Low  Power  Mode  and  Normal  Power  Mode,  TI  recommends  to  toggle  the 
LPWRB pin only after the button associated with that channel is released.

The Low Power Mode is also applicable for raw data access mode.

7.4.3 Configuration Mode

Before  configuring  any  register  settings,  the  device  must  be  put  into  the  configuration  mode  first.  Setting 
CONFIG_MODE  =  1  through 

Register  RESET  (Address  0x0A)

  stops  data  conversion  and  holds  the  device 

in  configuration  mode.  Any  device  configuration  changes  can  then  be  made.  The  current  consumption  in  this 
mode  is  typically  0.3  mA.  After  all  changes  have  been  written,  set  CONFIG_MODE  =  0  for  normal  operation. 
Refer to 

I

2

C Interface

 for more information.

7.5 Register Maps

7.5.1 LDC3114 Registers

LDC3114 Registers

 lists the memory-mapped registers for the LDC3114 registers. All register offset addresses 

not listed in 

LDC3114 Registers

 should be considered as reserved locations and the register contents should not 

be modified.

Table 7-1. LDC3114 Registers

Offset

Acronym

Register Name

Section

0h

STATUS

Device status

Section 7.5.1.1 

1h

OUT

Channel output logic states

Section 7.5.1.2 

2h

DATA0_LSB

The lower 8 bits of the Button 0 data (Two's 
complement

Section 7.5.1.3 

3h

DATA0_MSB

The upper 4 bits of the Button 0 data (Two's 
complement)

Section 7.5.1.4 

4h

DATA1_LSB

The lower 8 bits of the Button 1 data (Two's 
complement)

Section 7.5.1.5 

5h

DATA1_MSB

The upper 4 bits of the Button 1 data (Two's 
complement)

Section 7.5.1.6 

6h

DATA2_LSB

The lower 8 bits of the Button 2 data (Two's 
complement)

Section 7.5.1.7 

7h

DATA2_MSB

The upper 4 bits of the Button 2 data (Two's 
complement)

Section 7.5.1.8 

8h

DATA3_LSB

The lower 8 bits of the Button 3 data (Two's 
complement)

Section 7.5.1.9 

9h

DATA3_MSB

The upper 4 bits of the Button 3 data (Two's 
complement)

Section 7.5.1.10 

Ah

RESET

Reset device and register configurations

Section 7.5.1.11 

Ch

EN

Enable channels and low power modes

Section 7.5.1.12 

Dh

NP_SCAN_RATE

Normal Power Mode scan rate

Section 7.5.1.13 

Eh

GAIN0

Gain for Channel 0 sensitivity adjustment for 
button algorithm

Section 7.5.1.14 

Fh

LP_SCAN_RATE

Low Power Mode scan rate

Section 7.5.1.15 

www.ti.com

LDC3114

SNOSDD0 – DECEMBER 2021

Copyright © 2021 Texas Instruments Incorporated

Submit Document Feedback

15

Product Folder Links: 

LDC3114

Содержание LDC3114
























































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды