Terasic DE10-Agiles Скачать руководство пользователя страница 111

Страница: 111 / 208

DE10-Agilex
User Manual

111

www.terasic.com

January 29,

2021

devices refreshed at the appropriate intervals.



System Block Diagram

Figure 6-2

shows the system block diagram of this demonstration. In the

Platform

Designer

(formerly Qsys), one 50 MHz and four 166.667MHz clock source are used.

The four 166.667MHz clock source is provided by a dual frequency OSC that can

provide frequency to a 1:4 clock buffer, then fan out to four of differential clock pairs to

the FPGA for four DDR4 SO-DIMMs. The 50MHz is used by the

Intel FPGA

IOPLL

component to generate 200MHz for Nios Processor and On-Chip Memory. The four

166.667MHz clock are used as reference clocks for the DDR4 controllers. There are

four DDR4 Controllers which are used in the demonstrations. Each controller is

responsible for one DDR4-SODIMM. Each DDR4 controller is configured as a 4GB

DDR4-1333Mhz controller. The Nios II processor is used to perform the memory test.

The Nios II program is running in the On-Chip Memory. A PIO Controller is used to

monitor buttons status which is used to trigger starting memory testing.

Figure 6-2 Block diagram of the DDR4 Basic Demonstration

The system flow is controlled by a Nios II program. First, the Nios II program writes test

patterns into the whole 8GB of SDRAM. Then, it calls Nios II system function,

alt_dache_flush_all(), to make sure all data has been written to SDRAM. Finally, it

Содержание DE10-Agiles

















































































































































































































Результаты поиска

Содержание DE10-Agiles

Отзывы:

Бренды по названию

Популярные бренды

Terasic DE10-Agiles, Руководство пользователя

Результаты поиска

Содержание DE10-Agiles

Отзывы:

Бренды по названию

Популярные бренды