Tennant 3640G/LP Скачать руководство пользователя страница 2

Страница: 2 / 190

This service manual is intended to be an aid for the disassembly and reassembly of your TENNANT
Model 3640G/LP walk behind sweeper

The set is organized into five major groups: General Information, Chassis, Sweeping, Electrical,

and Engine G/LP.

General Information

: Safety precautions, machine transport, machine jacking, machine storage, chassis

lubrication, machine specifications, and machine maintenance chart.

Chassis:

Tire/wheel replacement, caster replacement, and transaxle repair.

Sweeping:

Hopper repair/replacement, brush repair/replacement, skirt/seal repair/replacement, and

sweeping troubleshooting.

Electrical:

Battery maintenance and replacement, electrical schematics, and electrical troubleshooting.

Engine -- GAS/LP:

Air filter replacement, oil changing, engine repair, engine troubleshooting, engine

removal, fuel system repair, and engine repairs.

Manual Number -- 330585

Revision: 01

Published: 12--01

CALIFORNIA PROPOSITION 65 WARNING:

Engine exhaust from this product contains chemicals known to the State of
California to cause cancer, birth defects, or other reproductive harm.

2000, 2001 TENNANT, Printed in U.S.A.

Содержание 3640G/LP































































































































































































Результаты поиска

Содержание 3640G/LP

Отзывы:

Tennant 3640G/LP, Руководство по обслуживанию, Страница: 2 / 190

Результаты поиска

Содержание 3640G/LP

Отзывы: