Tennant 3640G/LP Скачать руководство пользователя страница 12

Страница: 12 / 190

GENERAL INFORMATION

1-10

3640G/LP 330585 (12--01)

5. Block the machine tires and place the

directional control lever in Park. Tie down

the machine to the truck or trailer before

transporting.

Secure the rear of the machine by wrapping

straps around each end of the the handle

and fastening them to the truck or trailer.

Secure the front of the machine by wrapping

a strap around the hopper and fastening it to

the truck or trailer.

6. If the loading surface is not horizontal or is

higher than 380 mm (15 in) from the ground,

use a winch to unload machine.

If the loading surface is horizontal AND is

380 mm (15 in) or less from the ground, the

machine may be pushed off the truck or

trailer.

FOR SAFETY: When unloading machine

off truck or trailer, use winch. Do not

push the machine off the truck or trailer

unless the loading surface is horizontal

AND 380 mm (15 in) or less from the

ground.

Содержание 3640G/LP































































































































































































Результаты поиска

Содержание 3640G/LP

Отзывы:

Tennant 3640G/LP, Руководство по обслуживанию, Страница: 12 / 190

Результаты поиска

Содержание 3640G/LP

Отзывы: