Tennant 3640G/LP Скачать руководство пользователя страница 124

Страница: 124 / 190

SWEEPING

3-74

3640G/LP 330585 (5--00)

4. Pull the impeller straight up and off the shaft.

You may have to use a small pry bar or flat

screw driver to pry the impeller off. Do not

loose the key on the impeller shaft.

5. Remove the four hex screws and nuts

holding the bearing and pulley assembly to

the backing plate. Remove the bearing

assembly.

6. Loosen the set screws on the impeller belt

pulley. Slide the pulley off the impeller shaft.

NOTE:Make sure to mark the location of the

pulley on the impeller shaft for proper

re--assembly.

7. Use a press to remove the impeller shaft

and inner bearing from the bearing housing.

Press the bearing and shaft in the direction

of the fan shaft.

8. Press the second bearing out of the

housing.

Содержание 3640G/LP































































































































































































Результаты поиска

Содержание 3640G/LP

Отзывы:

Tennant 3640G/LP, Руководство по обслуживанию, Страница: 124 / 190

Результаты поиска

Содержание 3640G/LP

Отзывы: