Tennant 3640G/LP Скачать руководство пользователя страница 172

Страница: 172 / 190

ENGINE--GAS/LP

5-14

3640G/LP 330585 (5--00)

ENGINE CHOKE KNOB

An engine choke knob is standard equipment on

all LP gas powered machines.

On:

For cold starting, pull the engine choke knob

out.

Off:

Push the choke knob in.

LP CARBURETOR

The carburetor is similar to the one used on the

gas machine except for a few internal

modifications. A choke mechanism is also

employed on this carburetor. It is recommended

that the choke be pulled about half way closed for

optimum starting. There are no external

adjustments on the LP carburetor.

LP LOCK--OFF/FILTER

The LP lock--off/filter is mounted on the back of

the engine. The fuel line from the LP tank runs to

the inlet port on the lock--off/filter. The outlet port

on the lock--off is connected to the inlet port on

the LP regulator. The lock--off/filter functions

include removing impurities from the LP gas and

stopping the flow of LP gas when the engine is

not running.

LP REGULATOR

The LP regulator is mounted on the back of the

engine. The inlet port on the regulator is

connected to the outlet port of the lock--off/filter.

The outlet port on the regulator is connected by

hose to the LP carburetor. The LP regulator

senses engine vacuum and controls the amount

of LP fuel that flows to the carburetor. The LP

regulator is non--adjustable.

Содержание 3640G/LP































































































































































































Результаты поиска

Содержание 3640G/LP

Отзывы:

Tennant 3640G/LP, Руководство по обслуживанию, Страница: 172 / 190

Результаты поиска

Содержание 3640G/LP

Отзывы: