manualshive.com logo in svg

Teledyne PS200 Series, Руководство по эксплуатации и техническому обслуживанию, Страница: 11 / 58

Поделиться
Скачать
Teledyne PS200 Series Скачать руководство пользователя страница 11

PS200

PORTABLE GAS MONITOR

ABOUT THIS GUIDE

64171, Rev. 11/December 2019

1-1

1. ABOUT THIS GUIDE

This guide instructs gas detection personnel on the features and usage of the PS200 Portable Gas 

Monitor (or “the monitor”), including information on operation, configuration, maintenance, specifi

-

cations and troubleshooting.
This user guide assumes the reader has a basic knowledge of gas detection procedures. 
The user guide is divided into the following topics:

•

2. INTRODUCTION

•

3. OPERATION

 

•

4. ALARMS

•

5. WARNINGS & FAULTS

•

6. MANUAL BUMP TEST OPTIONS

•

7. RECHARGING THE BATTERIES

•

8. OPERATOR MAINTENANCE

•

9. CALIBRATION

•

10. ACCESSORIES*

•

APPENDIX A. OPERATING PARAMETERS & SENSOR TYPES

•

APPENDIX B. TECHNICAL SUPPORT

1.1. Guide Conventions

The following visual elements are used throughout this guide, where applicable: 

WARNING: THIS ICON AND TEXT INDICATE A POTENTIALLY HAZARDOUS 

SITUATION, WHICH, IF NOT AVOIDED, COULD RESULT IN DEATH OR 

INJURY.

CAUTION: This icon and text indicate an action or situation, which, if not avoided, 

could result in damage to the equipment.

NOTE: This icon and text designates information of special note.

WARNING: READ, UNDERSTAND AND FOLLOW THE ENTIRE CONTENT OF THIS 

GUIDE PRIOR TO USE. FAILURE TO DO SO MAY RESULT IN SERIOUS 

INJURY OR DEATH.

Содержание PS200 Series



























































Отзывы:

Нет отзывов