Teledyne PS200 Series Скачать руководство пользователя страница 47 | Manualshive

Страница: 47 / 58

Teledyne PS200 Series Скачать руководство пользователя страница 47

PS200

PORTABLE GAS MONITOR

OPERATOR MAINTENANCE

64171, Rev. 11/December 2019

8-1

8. OPERATOR MAINTENANCE
8.1. Cleaning

Clean the outer casing of the monitor using a non-abrasive moist cloth. Use a mild soap solution

with a non-abrasive cloth to remove stubborn marks.

8.2. Replace Filters

The monitor has 2 filters:
• hydrophobic (water) filter - located behind the filter cover on the front face of the monitor;
• sample inlet (dust) filter - located in the sample inlet connector at the bottom of the monitor.
Inspect these filters periodically for contamination or damage.

8.

2

.1. HYDROPHOBIC (WATER) FILTER REPLACEMENT

Figure 8-1: Hydrophobic Filter Replacement

• Using a No. 1 Pozidrive

®

screwdriver, unscrew the captive screw.

• Slide the filter cover away from the display until the locating lugs disengage from the locating

slots.

• Lift the filter cover away from the monitor.
• Remove the hydrophobic filter.
• Insert a new hydrophobic filter.

CAUTION: Do not use polishes that contain silicon or solvent to clean the monitor

as these may damage any flammable gas sensor fitted. Do not use

abrasive chemicals or strong, volatile chemical solutions as these could

damage the casing.

«
...
45
46
47
48
49
...
»

Содержание PS200 Series



























































Отзывы:

Нет отзывов