manualshive.com logo in svg

Teledyne PS200 Series, Руководство по эксплуатации и техническому обслуживанию, Страница: 21 / 58

Поделиться
Скачать
Teledyne PS200 Series Скачать руководство пользователя страница 21

PS200

PORTABLE GAS MONITOR

OPERATION

64171, Rev. 11/December 2019

3-1

3. OPERATION

Figure 3-1: Function Buttons

3.1. Operating Procedure

Check the following before use:
• The monitor is clean and in good condition.
• The filters are clean and in good condition.
• The sample line (pumped monitors) and any other accessories used are in good condition and 

leak-free.

• The battery is fully charged.
• There are no faults.
• All ranges are operational and the monitor is zeroed.
• The monitor is within the calibration period.

CAUTION: The monitor can be supplied with a flammable gas sensor. This sensor is 

designed for use in concentrations of gas not exceeding the Lower 

Explosive Limit (LEL). Exposing the sensor to concentrations of 

flammable gas above the LEL will not damage the sensor due to an 

inbuilt feature. Refer to 

Section 4. ALARMS

 for details.

NOTE: Throughout this document, the buttons will be referred to as L Button and R Button.

Содержание PS200 Series



























































Отзывы:

Нет отзывов