Teledyne PS200 Series Скачать руководство пользователя страница 6

Страница: 6 / 58

64171, Rev. 11/December 2019

PS200

PORTABLE GAS MONITOR

TABLE OF CONTENTS

Sect. # Section Title

Page #

6.4.

Quick/Full Bump Test

.....................................................................................................6-3

6.5.

Confirm Alarms

..............................................................................................................6-4

RECHARGING THE BATTERIES

.................................................................................7-1

7.1.

General

..........................................................................................................................7-1

7.2.

Recharge Monitor Using the Charging / Comms Clip

....................................................7-1

OPERATOR MAINTENANCE

.......................................................................................8-1

8.1.

Cleaning

........................................................................................................................8-1

8.2.

Replace Filters

...............................................................................................................8-1

CALIBRATION

...............................................................................................................9-1

9.1.

General Description

.......................................................................................................9-1

9.2.

Quick Calibration

...........................................................................................................9-2

9.3.

Calibration Validity

.........................................................................................................9-4

10.

ACCESSORIES*

.........................................................................................................10-1

OPERATING PARAMETERS & SENSOR TYPES

....................................................... A-1

A.1.

Typical Operating Parameters

...................................................................................... A-1

A.2.

LEL Sensor Types

........................................................................................................ A-2

TECHNICAL SUPPORT

............................................................................................... B-1

Содержание PS200 Series



























































Результаты поиска

Содержание PS200 Series

Отзывы:

Teledyne PS200 Series, Руководство по эксплуатации и техническому обслуживанию, Страница: 6 / 58

Результаты поиска

Содержание PS200 Series

Отзывы: