manualshive.com logo in svg

Teledyne PS200 Series, Руководство по эксплуатации и техническому обслуживанию, Страница: 22 / 58

Поделиться
Скачать
Teledyne PS200 Series Скачать руководство пользователя страница 22

PS200

PORTABLE GAS MONITOR

OPERATION

64171, Rev. 11/December 2019

3-2

• The oxygen sensor (if installed) operates correctly. The sensor responds to the user breathing 

on the front of the monitor by displaying a value below 20.9%.

Additional:
• Perform regular leak checks on pumped instruments by placing your thumb over the sample 

inlet nozzle and ensuring the monitor displays FLOW FAULT.

• Perform regular bump tests.

3.2. Quick Configuration Display

This allows configuration information to be viewed without fully switching the monitor ON (see 

Figure 3-2:

 

Quick Configuration Display

).

With the monitor OFF, press the R Button for less than one second. The monitor will display:
• sensors fitted;
• calibration due date;
• pumped or diffusion;
• LEL calibration gas.

Figure 3-2: Quick Configuration Display

3.3. Switching the Monitor On

Press and hold the R Button for one second to switch the monitor ON (refer to 

Figure 3-1:

 

Function 

Buttons

). The flash screen appears (as shown in 

Figure 3-3:

 

Flash Screen

) and the monitor begins 

its warm-up routine. A countdown timer appears in the top right corner of the display.

WARNING: ALWAYS SWITCH THE MONITOR ON IN FRESH AIR. FAILURE TO HEED 

THIS WARNING COULD RESULT IN SERIOUS INJURY OR DEATH.

NOTE: The LCD backlight is green during warm-up and automatically switches off when 

warm-up is complete.

Содержание PS200 Series



























































Отзывы:

Нет отзывов