Teledyne PS200 Series Скачать руководство пользователя страница 41 | Manualshive

Страница: 41 / 58

Teledyne PS200 Series Скачать руководство пользователя страница 41

PS200

PORTABLE GAS MONITOR

MANUAL BUMP TEST OPTIONS

64171, Rev. 11/December 2019

6-1

6. MANUAL BUMP TEST OPTIONS
6.1. Bump Testing

A bump test verifies sensor response and alarm operation by exposing the monitor to a known con

-

centration of gas.
The monitor has 2 manual bump test options:
• QUICK bump test validates sensors respond to gas and alarms are working.
• FULL bump test checks the response of all sensors against set limits and alarms are working.
By default, both of these options are disabled.
A bump test kit (Part No. 64051) is available and contains test gas, a regulator, and Tygon® tubing.

6.2. Initiating a Manual Bump Test

If enabled, switch the monitor ON by pressing the L button.
During warm-up, the BUMP TEST confirmation screen appears, as shown in

TEST Confirmation Screen

. Press the R button to continue.

Figure 6-1: BUMP TEST Confirmation Screen

When warm-up is complete, the APPLY GAS screen appears, as shown in

Screen (4-Gas Model)

WARNING: A QUICK BUMP TEST ONLY CHECKS THE OPERATION OF THE

AUDIBLE AND VISUAL ALARMS. IT DOES NOT VALIDATE SENSOR

ACCURACY OR RESPONSE TIME.

WHEN PERFORMING A BUMP TEST, THE TEST GAS CONCENTRATION

SHOULD BE HIGH ENOUGH TO TRIGGER THE MONITOR’S ALARMS. IF

ANY MONITOR FAILS A BUMP TEST, PERFORM A FULL CALIBRATION

BEFORE USING THAT MONITOR.

«
...
39
40
41
42
43
...
»

Содержание PS200 Series



























































Отзывы:

Нет отзывов