Telect LTX Скачать руководство пользователя страница 7

Страница: 7 / 35

LTX Patch and Splice Panel

Installation Guide

1.509.926.6000 :: telect.com

LTX 1RU

The Telect LTX patch and splice panel consolidates

network fiber splicing, patching and routing requirements

in a 1RU panel.

The LTX 1RU panel accommodates:

•

Up to 72 fiber terminations

•

Stacked splice trays, housing 36 splice sleeve holders

per single fusion tray and 144 per mass fusion tray

•

Single fusion/mass fusion options

•

Velcro bands that secure trays inside the panel

•

Routing spools to manage slack cable routing

•

Panel mounted cable clamp for incoming cable

slack maintanence

•

Designation label on the front

Interconnect and cross-connect cabling enter the LTX

panel at rear corner locations guided over rubber edge

protectors. Slack storage area in the rear of the panel

routes IntraFacility Cables (IFC) through the panel to

splice trays in the center of the panel. After splicing,

pigtail fibers connect to patch plate mounted connectors

at the rear of the panel and fiber jumpers connect to

patching adapters at the front.

LTX patch and splice panel patch plates

can accommodate:

•

SC/UPC, SC/APC, LC/APC, LC/UPC are available in

patch plates with 6 or 8 terminations

•

LC/SC available in patch plates with

12 terminations

•

LC/UPC and LC/APC available in patch plates with

24 terminations

•

MPO/MTP feed through patch plates available with 6

or 8 adapters

In addition, Telect offers a special factory-configured

integrated 1RU patch plate panel with up to 72

terminations (requires use of LC quad adapters).

Adapters are also offered in multi-mode versions. All

adapters include dust covers. All patch plates are

available in white or black.

Figure 1-2-1 - LTX 1RU Patch and Splice Panel Overview

- Front and Rear Views-

Designation Label

LTX Patch and Splice Panel, Front View

(24 terminations shown)

Bracket

LTX Patch and Splice Panel, Rear View

(

24 terminations shown)

Bracket

Routing Spool

Splice Tray

Patch Plate

Patch Plate with Adapters

Velcro Tie

Содержание LTX




































Результаты поиска

Содержание LTX

Отзывы:

Бренды по названию

Популярные бренды

Telect LTX, Руководство по установке

Результаты поиска

Содержание LTX

Отзывы:

Бренды по названию

Популярные бренды