manualshive.com logo in svg

Telect LTX, Руководство по установке

Поделиться
Скачать
Telect LTX Скачать руководство пользователя страница 16

LTX Patch and Splice Panel

Installation Guide 

© Telect, Inc.  All rights reserved. 148326 12.20.16 v2

1.509.926.6000  ::  telect.com

16

The installation instructions apply to the 

LTX 2RU & 1RU

Refer to 

Figure 3-5-1 & Figure 3-5-2

 for 

this procedure.

Incoming cables route from above or 

below and enter the LTX panel at one 

of the upper rear corners. The cable 

clamp bracket is used to house the 

cable clamp which secures the cable to 

the panel.

1.  Position cable clamp bracket with 

the straight side up and the angled 

side facing down on the outside 

upper corner edge at the rear of the 

LTX Panel. 

2.  Align the two screw holes in the 

top portion of the bracket with the 

screw holes at the top edge of the 

rear overhang on the LTX panel.

3.  Insert two Phillips screws through 

the bracket from the outside into 

the panel edge screw holes 

 

and tighten.

 

* Leave sufficient IFC slack to allow 

drawer to open properly.

Figure 3-5-1 2RU Cable Clamp Bracket Installation

Figure 3-5-2 1RU Cable Clamp Bracket Installation 

LTX Panel

Upper Rear 

Corner

Cable 

Clamp 

Bracket

Screws

LTX Panel

Upper Rear 

Corner

Screws

Cable Clamp  

Bracket

Содержание LTX




































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды