manualshive.com logo in svg

Telect LTX, Руководство по установке

Поделиться
Скачать
Telect LTX Скачать руководство пользователя страница 22

LTX Patch and Splice Panel

Installation Guide 

© Telect, Inc.  All rights reserved. 148326 12.20.16 v2

1.509.926.6000  ::  telect.com

22

3.1.11 Installing Mounting Brackets on the LTX Panel

The installation instructions apply to the 

LTX 4RU, 2RU 

& 1RU 

Refer to 

Figure 3-11, Figure 3-11-1 & Figure 3-11-2  

for this procedure.

The LTX panel mounting brackets are used to attach 

the LTX panel to a 19" or 23" EIA, ETSI or WECO rack.  

There are two rows of screw holes along the inside 

walls of the LTX panel that can be used for mounting 

brackets to the LTX panel.

1.  Align mounting bracket screw holes with the screw 

holes in the sidewall of the LTX panel.

2.  Insert screws through outside holes of the bracket 

into the panel sidewall.

3.  Using a Phillips screwdriver, tighten screws to 

secure the bracket to the panel.

4.  Repeat Steps 1 - 3 to mount bracket on adjacent 

sidewall of the LTX panel. 

LTX 4RU Panel

Mounting  

Bracket

Screws

Figure 3-11 Installing Mounting Brackets on LTX 4RU Panels

Figure 3-11-2 Installing Mounting Brackets on LTX 1RU Panels

LTX 1RU Panel

Mounting Bracket

Screws

Figure 3-11-1 Installing Mounting Brackets on LTX 2RU Panels

Screws

Mounting  

Bracket

LTX 2RU Panel

Содержание LTX




































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды