manualshive.com logo in svg

Telect LTX, Руководство по установке

Поделиться
Скачать
Telect LTX Скачать руководство пользователя страница 19

LTX Patch and Splice Panel

Installation Guide 

© Telect, Inc.  All rights reserved. 148326 12.20.16 v2

1.509.926.6000  ::  telect.com

19

3.1.8 Adapter Patch Plate Installation

The installation instructions apply to the 

LTX 4RU, 2RU 

& 1RU

Refer to 

Figure 3-8, Figure 3-8-1 & 3-8-2 

for this procedure.

The adapter patch plate installs at the front of the LTX 

patch and splice panel. The patch plate comes with 

adapters pre-installed. Pigtail fibers from the splice tray 

will connect to connectors at the rear and fiber jumpers 

will connect to adapters at the front of the patch plate.

1.  Position the patch plate at the front of the LTX 

patch and splice panel with fiber jumper adapters 

facing toward the front of the LTX panel and pigtail 

connectors facing the rear of the LTX panel.

2.  On one side of the LTX panel, align top and bottom 

screw holes with patch plate screw holes. (4RU)

3.  From the outside of the LTX panel, insert screws and 

hand tighten.

4.  On the other side of the LTX panel, align top and 

bottom screw holes with patch plate screw holes.

5.  From the outside of the LTX panel, insert screws and 

hand tighten.

6.  Ensure patch plate is centered and there is a little 

clearance around the plate and the panel.

7.  Use a Phillips screwdriver to tighten all four 

screws.

 

Adapter Patch Plate

  

(144 SC Terminations shown)

Screws 

Screws

 

Some clearance between Patch 

Plate and LTX Panel

LTX 4RU Panel

Front View

Figure 3-8 4RU Adapter Patch Plate Installation 

LTX 2RU Panel 

Front View

Adapter Patch Plate

(48 Terminations Shown)

Some clearance between Patch 

Plate and LTX Panel

Screws

Screws 

Figure 3-8-1 2RU Adapter Patch Plate Installation

Figure 3-8-2 1RU Adapter Patch Plate Installation

LTX 1RU Panel 

Front View

Adapter Patch Plate

(48 Terminations Shown)

Some clearance between Patch 

Plate and LTX Panel

Screws 

Screws 

 

* Patch plates on the 2RU & 1RU are attached to         

  the tray, not on the chassis like the 4RU.  

Содержание LTX




































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды