Telect LTX Скачать руководство пользователя страница 12

Страница: 12 / 35

LTX Patch and Splice Panel

Installation Guide

1.509.926.6000 :: telect.com

Chapter 3: LTX Patch and Splice Panel Installation and Routing

3.1 LTX Panel Component Installation

If not already installed, install LTX panel components prior to installing cabling and fibers, or mounting the

panel to a rack.

LTX panel components include entry/exit arcs, splice tray platform with routing spools, velcro banding, stacked splice

trays, one or two cable clamp brackets with cable clamps, front and rear doors, designation cards for front and rear of the

panel and an adapter patch plate panel with connectors and adapters.

3.1.1 Entry/Exit Arc Installation

Refer to

Figure 3-1

for this procedure.

The installation instructions apply to the

LTX 4RU

only

At the front of the LTX panel, four entry/exit split arcs protect

top and bottom corners where fiber jumpers enter the panel.

At the rear of the panel, entry/exit split arcs protect top and

bottom corners where IntraFacility Cables (IFC) enter the LTX

panel. Arcs can be removed if needed to accommodate other

LTX panel attachments.

At each corner of the LTX panel:
1. Position the center groove of the entry/exit arc in front of the

metal edge on the LTX panel.

2. Slide the entry/exit arc onto the corner entryway.

NOTE: The arcs install in the rear of the panel.

LTX Patch and Splice Panel

Side View

Arc

Center

Groove

Arc

Front View

Arc

Door

3.1.2 Routing Spool Installation

Figure 3-1 - Entry/Exit Arc Installation

Refer to

Figure 3-2

for this procedure.

The installation instructions apply to the

LTX 4RU

2RU

1RU

Follow these instruction incase spools are not already installed

by the manufacturer. Routing spools are installed on the tray

platform before the platform is installed in the LTX panel.

Routing spools protect centrally located splice trays and

route IFC in the rear of the LTX panel through the slack

storage area.

1. On the tray platform, locate the four routing spool

screw holes.

2. Position routing spools on the tray platform so that screw

holes align. For correct alignment, the routing spool

overhang should face toward the outside of the platform.

3. Insert a screw from the bottom of the tray platform up

and into the screw hole of each routing spool and

hand tighten.

4. Adjust routing spool positions to best accommodate cable

routing and tighten screws using a Phillips screwdriver.

Routing Spools

Tray Platform

Tie-Down

Slot

Platform

Thumb Screw

Routing Spool Screw

Attaches through bottom of

tray platform

Routing Spool

Overhang

Figure 3-2 - Routing Spool Installation

Содержание LTX




































Результаты поиска

Содержание LTX

Отзывы:

Бренды по названию

Популярные бренды

Telect LTX, Руководство по установке

Результаты поиска

Содержание LTX

Отзывы:

Бренды по названию

Популярные бренды