manualshive.com logo in svg

Tektronix TLA 720, Руководство по обслуживанию

Поделиться
Скачать
Tektronix TLA 720 Скачать руководство пользователя страница 64

TLA 720 Benchtop Chassis and TLA 7XM Expansion Chassis Service Manual

2–25

Command Groups

This section lists mainframe commands by functional groups. A question symbol
surrounded by brackets [?] identifies commands that also have a query form.

Status Commands

Commands in the STATus subsystem, along with several IEEE 488.2 Common
Commands, control the status and event reporting system. 

Table 2–8: Status commands 

Header

Description

:BLOWer?

Returns the contents of the Blower Event register.

:CONDition?

Returns the contents of the Blower Condition register.

:CURRent?

Returns the contents of the Current Event register.

:CMAXimum?

Returns the maximum current level since power on.

:CONDition?

Returns the contents of the Current Condition register.

:LEVel?

Returns current level.

:LIMit

[?]

Sets or queries the maximum current usage allowed
before generating an alarm.

:MAXimum?

Returns the maximum current level since the last factory
maintenance.

:ENABle[?]

Sets or queries the contents of the Blower Enable
register.

:SPEed?

Returns the fan speed in revolutions per minute.

:CONDition?

Returns the contents of the Questionable Condition
register.

:ENABle[?]

Sets or queries the contents of the Questionable Status
Enable register.

:CMAXimum?

Returns the maximum power used since power up.

:CONDition?

Returns the contents of the power condition register.

:ENABle

[?]

Sets or queries the contents of the power enable
register.

:LEVel?

Returns the wattage used by the mainframe.

:LIMit

[?]

Set or query the maximum amount of power allowed
before generating an alarm.

Содержание TLA 720























































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды