manualshive.com logo in svg

Tektronix TLA 720, Руководство по обслуживанию

Поделиться
Скачать
Tektronix TLA 720 Скачать руководство пользователя страница 126

TLA 720 Benchtop Chassis and TLA 7XM Expansion Chassis Service Manual

3–1

Theory of Operation 

This section provides a brief overview of the theory of operation for the
benchtop chassis. Figure 6–1 and 6–2 on page 6–1 shows a functional block
diagram.

Benchtop Chassis

The standard chassis contains the following major modules:

H

Power supply

H

Backplane

H

Enhanced monitor board

H

Temperature sense board

The power supply provides all voltages and currents to the chassis. The power
supply connects to the backplane at J1 and J2 through the power supply interface
board.  

The backplane (A4) provides all the connections to module slots 0 through 12 in
the chassis. It also has connections to all other circuit boards and modules in the
chassis.  

The front panel On/Standby DC switch connects to one of two connectors at the
top of the backplane. When the switch is connected to J22, the switch controls
the power in the chassis. When the switch is connected to J23, the power-on
functions are controlled by an external source through the 25-pin connector on
the enhanced monitor board. Although the switch still illuminates when power is
applied to the chassis, the on/off function of the switch is disabled.

A 34-wide ribbon cable at 0J4 on the backplane connects to J16 on the tempera-
ture sense board. Connectors 0J1, 0J2, and 0P3 carry instrument monitoring
information from the backplane to the enhanced monitor board.

Power Supply and Power

Supply Interface Board

Backplane

Содержание TLA 720























































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды